Página 1
4573439N (Light Gray Velvet) 4389639N (Blue Linen) 4296439N (Dark Grey Linen) 4390339N (Ivory Linen) 4297939N (Green Linen) Upholstered Bed with Storage Drawers Queen Size Weight Limit: Thank you for purchasing from DHP! Bed: 500Lb/227Kg Drawer: 40Lb/18Kg DO NOT RETURN TO THE STORE ! If parts are missing or damaged, we will gladly ship your replacement parts free of charge.
Página 2
Limited 1 year Warranty Read Before Beginning Assembly DHP warrants this product to be free from defects in material and workmanship Work in a spacious area and near where the unit will be used, preferably on a and agrees to remedy any such defect. This warranty covers one year from the carpet, or use a piece of the cardboard packaging to protect your floor and product.
Página 4
Footboard Side Rail Side Rail Headboard Back Panel Center Rail Bracket Guide Support Rail Wooden Slats X 24 PART NUMBERS 4573439N 4390339N 4297939N 4296439N PART 4389639N IMPORTANT: (Light Gray Velvet) Ivory Linen (Green Linen) (Dark Grey Linen) LABELS Blue Linen...
Página 5
Drawer Side Panel Drawer Side Panel X 20 Front Panel Single Slat Cap Double Slat Cap X 24 X 12 PART NUMBERS 4297939N 4573439N 4389639N 4390339N 4296439N PART IMPORTANT: (Green (Light Gray Velvet) (Blue Linen) Ivory Linen (Dark Grey Linen)
Página 6
Hardware Pack Please do not completely tighten all the hardware, until the entire assembly is complete, unless otherwise indicated in the step-by-step instructions. 4573439N (Light Gray Velvet) HP#:T4155429-00 4389639N (Blue Linen) 4296439N (Dark Grey Linen) The screw(s), bolt(s) to be used at each step are...
Página 7
Step 1 Stick A1 to the back of A with Velcro as illustrated.
Página 9
Step 3 Attach G X 2 to K with Fully tighten all bolts in this Step.
Página 10
Step 4 Attach E and F to G with Don't completely tighten the bolts until STEP 6 is complete.
Página 11
Step 5 Attach E and F to A and B with...
Página 12
Step 6 6.1 Attach I x2 to A and B with 6.2 Attach I x2 to K with , then properly tighten all the bolts. The slat holes should be The slat holes should be oriented towards upside. oriented towards upside.
Página 13
Step 7 7.1 Insert O1 into X , 7.2 Press X into E & F , repeat the same procedure for the opposite side of the bed with a new O1 and X . 7.3 Insert ends of both slats O1 into Y , then press Y into I as illustrated.
Página 14
Step 8 Attach M to S and N with don't completely tighten the bolts until STEP 10 is complete. For better performance, please orient the plastic sheet towards inside of the drawer. Make sure that these holes are all located on the top side before assembling X 16...
Página 15
Step 9 9.1 Attach Q to L with 9.2 Attach Q X 4 and L to S and N with 9.3 Attach L to M with X 32...
Página 16
Step 10 Attach sub-assembly L/S/N/M from previous step to C with , then properly tighten all the bolts. X 24...
Página 18
Step 12 Align Drawers with the bed frame and push them into the bed. Lock drawers by slightly lifting drawer and Slot inserting the Pin into the Slot. Slot...
Página 19
CAUTION: This unit is intended for use only with the products and/or maximum Helpful Hints weights indicated. Use with other products and/or products heavier than the maximum weights indicated may result in instability or cause possible injury. Move your new furniture carefully, with two people lifting and carrying the unit to its new location.
Página 20
Informaci n sobre la garant a Lea antes de comenzar a ensamblar DHP garantiza que este producto est libre de defectos de material y mano de Llame a nuestro n mero gratuito si necesita asistencia. obra y se compromete a remediar cualquier defecto de este tipo. Esta garant a Trabaje en un rea espaciosa y cerca de donde su producto ser utilizado, cubre 1 a o a partir de la fecha de compra original.
Página 21
Tambi n confirme que ha recibido todos los componentes necesarios para el real en la esquina inferior derecha de cada p gina. ensamblaje al compararlos con la tabla de piezas indicadas en la secci n en ingl s. N MERO DE PIEZA 4573439N 4297939N 4296439N ETIQUETAS DE 4389639N...
Página 22
Instrucciones Limites de peso - Cama : 500Lb/227Kg Paso 1 Coloque A1 en la parte posterior de A con el cierre m gico como se ilustra. Limites de peso - Cama deslizable: 40Lb/18Kg Paso 2 Consejos tiles Una J X 2 con A y B con los Paso 3 Mueva sus muebles nuevos con cuidado, se requiere de dos personas para levantar y trasladar su mueble a su nueva ubicaci n.
Página 23
Merci d'avoir achet un produit DHP ! Informations sur la garantie Avant de commencer l'assemblage DHP garantit que ce produit est exempt de tout vice de mat riaux et de fabrication Si vous avez besoin d'aide, appelez notre service la client le sans frais.
Página 24
Pi ces Quincaillerie Pour des pi ces de rechange, visitez www.dhpfurniture.com/fre/replacement-parts # de paquet : T4155429-00 IMPORTANT: La liste des r f rences ci-dessous est propre votre produit. Remarque: Sauf indication contraire dans les instructions, ne pas resserrer Veuillez l'avoir sous la main lorsque vous appelez pour des pi ces de rechange. compl tement les vis et les boulons, jusqu' ce que l'assemblage soit termin .
Página 25
Instructions Limite de Poids - Lit : 500Lb/227Kg tape 1 Coller A1 l'arri re de A avec le Velcro, comme illustr . Limite de Poids -Lit gigogne:40Lb/18Kg tape 2 Conseils utiles Attacher J X 2 A et B avec D placez votre nouveau mobilier avec soin, nous recommandons deux tape 3 personnes pour soulever et transporter le mobilier vers son nouvel AttacherG X 2...