Publicidad
Idiomas disponibles
Idiomas disponibles
Installing and Removing the Battery Pack from
the tool
Warning! Make certain the lock-off button is engaged to
prevent switch actuation before removing or installing battery.
To install battery pack (Fig. C)
Insert battery pack firmly into tool until an audible click is
u
heard as shown in figure C. Ensure battery pack is fully
seated and fully latched into position.
To remove battery pack (Fig. D)
Depress the battery release button (5b) as shown in
u
figure D and pull battery pack out of tool.
Belt hook (Optional extra) (Fig. E, F)
Warning! To reduce the risk of serious personal injury,
place the forward/reverse button in the lock-off position or
turn tool off and disconnect battery pack before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Warning! To reduce the risk of serious personal injury, ONLY
use the tool's belt hook (8) to hang the tool from a work belt.
DO NOT use the belt hook (8) for tethering or securing the
tool to a person or object during use. DO NOT suspend tool
overhead or suspend objects from the belt hook.
Warning! To reduce the risk of serious personal injury, ensure
the screw (9) holding the belt hook is secure.
Note: When attaching or replacing the belt hook (8), use only
the screw (9) that is provided. Be sure to securely tighten
the screw.
The belt hook (8) can be be attached by sliding into the
slots (10) on either side of the tool.
using only the screw (9) provided, to accommodate left- or
right-handed users. If the hook is not desired at all, it can be
removed from the tool.
To move the belt hook, remove the screw (9) that holds the
belt hook (8) in place then reassemble on the opposite side.
Be sure to securely tighten the screw (9).
Note: Various trackwall hooks and storage configurations
are available.
Please visit our website www.stanley.eu/3 for
further information.
Fitting and removing a screwdriver bit or socket
(Fig. G, H)
This tool is fitted with a quick release chuck to allow for an
easy exchange of bits.
Warning! Make certain the tool is locked to prevent switch
actuation before installing or removing accessories.
Lock the tool by setting the forward/reverse slider (2) to
u
the centre position.
Insert the bit shaft (11) into the quick release chuck (3)
u
(Fig. G).
(Original instructions)
Note! To remove the bit/socket, pull and hold the chuck
collar (4) away from the front of the tool (Fig. H).
Warning! Use only impact rated sockets. Non-impact sockets
may break and cause a hazardous condition. Inspect socket
prior to use to ensure that it contains no cracks. Use only
impact rated accessories.
Use
Warning! Let the tool work at its own pace. Do not overload.
Selecting the direction of rotation (Fig. I)
For tightening, use forward (clockwise) rotation. For loosening,
use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse
u
slider (2) to the left.
To select reverse rotation, push the forward/reverse slider
u
to the right.
To lock the tool, set the forward/reverse slider into the
u
centre position.
Screwdriving / nut setting
Select the appropriate bit / socket for the screw or nut to
u
be driven.
Select forward or reverse rotation as described above.
u
Hold the tool in line with the fastener.
u
Press the trigger (1)
u
After tightening, check torque with a torque wrench.
u
LED work light
The LED work light (6) is activated automatically when
the trigger is depressed. The LED work light will illuminate
when the trigger is partially depressed, before the unit
begins running.
Hints for optimum use
Screwdriving
Always use the correct type and size of screwdriver bit.
u
If screws are difficult to tighten, try applying a small
u
amount of washing liquid or soap as a lubricant.
Always hold the tool and screwdriver bit in a straight line
u
with the screw.
Maintenance
Your STANLEY tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
ENGLISH
23
Publicidad
