Bosch Nexxt 800 Serie Operacion, Cuidado E Instrucciones Para La Instalacion página 8

DONOTassemble theductwork w ith
screws orfasteners thatextend intothe
duct.They willserve asan
accumulation point f orlint.
Joints should besecured with
aluminum tape.
Exhaust vent hood
The exhaust duct must end with an
approved exhaust vent hood with
swing out damper(s). DO NOT use an
exhaust vent hood with magnetic
latches.
To avoid exhaust restriction, the outlet
must be a minimum of 12 inches (30
cm) above ground level or any other
obstructing surface.
Bottom exhaust kit
All joints should be tight to avoid leaks.
The male end of each duct section
must point away from the dryer.
Whether connecting to an existing
venting system or a new venting
system, make sure that all ducting is
clean and free of lint.
The maximum permitted length for both
rigid and flexible metal duct is shown in
the table below.
Number of RigidDuct Flexible Duct
90° Turns
or Elbows
0 66 ft. 45 ft.
(2011 cm) (1372 cm)
1 56 ft. 36 ft.
(1707cm) (1097 cm)
2 48 ft. 29 ft.
(1463cm) (884 cm)
3 39 ft. 22 ft.
(1189cm) (671 cm)
4 3Oft. 16 ft.
(914cm) (488 cm)
Note:
Side and bottom exhaust installations
have a 90° turn inside the dryer. To
determine maximum exhaust length,
add one 90 °turn to the chart.
More than two 90 ° turns are not
recommended. For best performance,
separate all turns by at least 4 ft. of
straight duct, including distance
between last turn and exhaust hood.
Good
Better
Required parts
The parts required for the exhaust air
system (elbows, lines, exhaust air
outlets) are not included in standard
delivery of the dryer.
Accessories
The parts required for the exhaust air
system can be obtained from customer
service or your local dealer. Please
follow the installation instructions
supplied by the appropriate
manufacturer!
;ide exhaust kit
part no. WTZ 1265
Note:
The maximum permitted number of 90 °
elbows (including this side exhaust kit)
is four!
[_ Special tool for cutting the hole in
prepared side panel is required.
Contact local dealer!
part no. WTZ 1270
Note:
The maximum permitted number of 90°
elbows (including this side exhaust kit)
is four!
Left hinge kit
part no. WTZ 1260 for all dryers except
duo tone silver
part no. WTZ 126S for duo tone silver
dryers
The door catch can be reversed if
necessary. The door is hinged on the
right at the factory.
Pedestal Mounting Kit
Part no. WTZ 1295 (for white dryer).
Part no. WTZ 1295P (for duo tone
dryer)
If mounting the dryer on the pedestal
follow the instructions supplied with the
pedestal.
Installation- step by step
1. Unpack the dryer.
2. Remove all objects from the drum.
3. Check the dryer for visible
damage.
4. Position the dryer near the
installation location.
5. If required, change the door hinges
to the left
(see page 5).
6. If required install the exhaust air
outlet on the dryer
(see page 7).
7. Have the power supply cord fitted
by an authorized technician (see
page 8).
8. Install exhaust duct, if necessary.
Follow the installation instructions
supplied by the appropriate
manufacturer!
,
If space is very restricted, it is
recommended to fit the initial parts
of the exhaust duct to the dryer
before the dryer is moved to its
final installation location.
Move the dryer to its final location
and align.