HIKOKI C 3607DB Instrucciones De Manejo página 14

English
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains
the accessories listed on page 152.
Standard accessories are subject to change without notice.
APPLICATIONS
Cutting various types of wood.
SPECIFICATIONS
1. Power tool
Model
Voltage
No-load speed
Blade external dia.
Blade hole dia.
Cutting
Capacity
depth
Battery available for this
tool* 1
Weight* 2
*1 Existing batteries (BSL3660/3620/3626, BSL18 series,
etc.) cannot be used with this tool.
If using the AC/DC Adapter, please read and
understand its manual before operating the power tool.
*2 According to EPTA-Procedure 01/2014
NOTE
Due to HiKOKI's continuing program of research and
development, the specifications herein are subject to
change without prior notice.
Electronic control
○ Soft-start
○ Brake function
Battery; Small counter-force
AC/DC Adapter; Large counter-force
– Please be aware that the counter-force of the brake
differs depending on the battery being used.
○ Overload protection
This protection feature cuts off the power to the motor in
the event of overloading of motor or a conspicuous
reduction in rotational speed during operation.
When the overload protection feature has been
activated, the motor may stop.
In this case, release the tool switch and eliminate
causes of overloading.
After that you can use it again.
○ Overheat protection
This protection feature cuts off the power to the motor
and stops the power tool in the event of overheating of
motor during operation.
When the overheat protection feature has been
activated, the motor may stop.
C3607DB
36 V
6000 min- 1
(Auto Switch mode)
4500 min-
1
(High Torque mode)
190 mm
30 mm
90° 64.5 mm
45° 49 mm
Multi volt battery /
AC/DC Adapter
(sold separately)
4.3 kg (BSL36A18X)
4.6 kg (BSL36B18X)
In this case, release the tool switch and cool it down in a
few minutes.
After that you can use it again.
○ Rotation speed changeover function (Auto Switch
mode / High Torque mode)
○ Precaution for continuous cutting
When using AC/DC Adapter if the switch is repeatedly
switched ON and OFF during a short period of time
while in the Auto Switch mode, the tool will be stopped
early by the overheat protection feature. When that
happens, using the High Torque mode is
recommended.
2. Battery
Model
BSL36A18X
*1 The tool itself will automatically switch over.
CHARGING
Before using the power tool, charge the battery as follows.
<UC18YSL3>
1. Connect the charger's power cord to the
receptacle.
When connecting the plug of the charger to a
receptacle, the charge indicator lamp will blink in red.
(See Table 1)
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 10 (on page 3).
3. Charging
When inserting a battery in the charger, charging will
commence and the charge indicator lamp will blink in
blue.
When the battery becomes fully recharged, the charge
indicator lamp will light up in green. (See Table 1)
(1) Charge indicator lamp indication
The indications of the charge indicator lamp will be as
shown in Table 1, according to the condition of the
charger or the rechargeable battery.
Table 1: Indications of the charge indicator lamp
ON/OFF at 0.5 sec. intervals
(RED)
Lights for 0.5 sec. at intervals of
1 sec. (BLUE)
Lights for 1 sec. at intervals of
0.5 sec. (BLUE)
Lights continuously (BLUE)
Lights continuously (Continuous
buzzer sound: about 6 sec.)
(GREEN)
ON/OFF at 0.3 sec. intervals
(RED)
14
Voltage Battery capacity
36 / 18 V* 1 2.5 / 5.0 Ah*
Before charging *
Charged at less than
50%
Charged at less than
80%
Charged at more
than 80%
Charging complete
Overheat standby *
1
1
2