Publicidad
circumstances.
f)
Wear suitable work clothes. Do not wear
loose clothing or jewellery. Keep hair, clo-
thes and gloves away from moving parts.
Loose clothing, jewellery or long hair can get
trapped in moving parts.
g) If vacuuming devices and draining de-
vices can be fi tted, make sure that these
are correctly attached and correctly used.
The use of a dust extraction system can redu-
ce the danger posed by dust.
Do not lose this safety information.
4. Usage and treatment of the electric tool
a) Do not overload the appliance. Use the
correct tool for your work. You will be able
to work better and more safely within the gi-
ven performance boundaries.
b) Do not use an electric tool with a defec-
tive switch. An electric tool that cannot be
switched on or off is dangerous and must be
repaired.
c) Pull the plug out of the socket and/or
remove the battery before making any ad-
justments to the appliance, changing ac-
cessories or put the appliance down. This
safety measure prevents starting the electric
tool unintentionally.
d) Keep unused electric tools out of the
reach of children. Do not allow people
who are not familiar with the appliance or
who have not read these instructions to
use the appliance. Electric tools are dange-
rous if they are used by inexperienced people.
e) Clean your electric tool carefully. Check
whether moving parts are functioning
properly and not jamming, whether parts
are broken or damaged enough that the
functioning of this electric tool is aff ec-
ted. Have damaged parts repaired before
using the appliance. Many accidents are
caused by badly maintained electric tools.
f)
Keep your cutting tools sharp and clean.
Carefully maintained cutting tools with sharp
cutting edges will jam less and are easier to
control.
g) Make sure to use electric tools, accesso-
ries, attachments, etc. in accordance with
these instructions. Take the conditions in
your work area and the job in hand into
account. Using electric tools for any purpose
other than the one for which they are intended
can lead to dangerous situations.
Anl_SA_TC_HA_2000_1_SPK8.indb 11
Anl_SA_TC_HA_2000_1_SPK8.indb 11
GB
5. Service
a) Have your electric tool repaired only by
trained personnel using only genuine
spare parts. This will ensure that your elec-
tric tool remains safe to use.
Do not lose these safety instructions
Additional safety instructions:
•
Ensure that the ON/OFF switch is set to "0"
(OFF) before you insert the plug into the so-
cket.
•
The nozzle reaches temperatures of up
to 550°C. Fire hazard! Wear protective
gloves and eye wear. The nozzle should
not be touched during operation.
•
Allow the hot air pistol to completely cool be-
fore putting away.
•
Never expose the unit to rain or moisture.
Store the unit in a dry place.
•
Do not leave the unit unattended. Keep out of
reach of children.
•
Never direct the air flow at people or ani-
mals. Do not use the unit to dry clothing
or hair. Do not use the hot air blower as a
hair dryer.
•
Do not use the unit near easily flammable or
explosive substances or gasses.
•
Never block the hot air flow by plugging or
covering the air flow exit.
•
Use only original accessory and replacement
parts from the manufacturer.
•
Do not wear loose clothing or jewelry. Wear
slip-resistant shoes and wear a hair net for
long hair. During operation maintain a secure
footing.
•
Never use the unit in wet surroundings or in
areas with high humidity (bathroom, sauna,
etc.).
•
Check your work area for easily flammable
substances and materials before using the
hot air pistol.
•
Never carry the hot air pistol by the power
supply cord.
•
Only use extension cords with a minimum
cross-section area of 1,5 mm
•
Repairs (for example power supply cord
replacement) should be performed only by a
qualified electrician.
•
Do not use chemical paint removers or sol-
vents at the same time as the hot air pistol.
•
Clean the nozzle when soiled.
•
Be sure that the openings for air entry and
exit are always clean and free of dirt.
•
Hazardous or poisonous gasses can be freed
when removing paint. Be sure to provide ade-
- 11 -
.
2
14.04.16 10:04
14.04.16 10:04
Publicidad
