Nemox crea Serie Instrucciones Para El Uso página 9

PRESERVATION CYCLE VARIATION WHILE A
PROGRAM IS RUNNING
During the preparation phase it is possible to
automatically vary the preservation cycle set at
any time. Repeatedly press button (12) until the
LED that corresponds to the desired cycle is
activated. The LED will flash for 3 seconds and
becomes steadily lit: the new preservation cycle
is selected at this point and will be performed at
the end of the program. Each preparation
program will activate at the end of the selected
preservation cycle.
PADDLE LOCK UPON LID OPENING
The opening of the lid (3) only stops paddle (5)
and does not affect the preparation program.
The closure of the lid (3) starts the motion of the
paddle (5) (where, at that time it is provided by
the selected program). If the mixture proves
excessively thick to prevent the movement of
the paddle, the machine will automatically
activate the previously selected preservation
cycle.
PADDLE SPEED ADJUSTMENT
The paddle rotation speed is adjustable by
means of the knob (8).
The adjustment of the paddle speed is
completely independent from the execution of
programs and can be changed at any time.
Air intake into the mixture varies according to
the recipe and paddle rotation speed.
To a lower number of revolutions corresponds a
higher density. (less air incorporated into the ice
cream). To a greater number of revolutions
corresponds a smaller density of the product
(more air incorporated into the ice cream)
We recommend you use low speeds when
preparing classic Italian gelato, Granita and
sorbet, and high speeds when preparing semi-
soft Italian gelato.
AUTOMATIC PRESERVATION
There are 4 preservation cycles available for
every whipping program (total of 16 cycles)
devised to meet a wide range of needs.
•In automatic mode, if the machine is not
stopped, at the end of each production cycle
is enabled the ice cream preservation cycle
selected.
•The activation of the preservation function is
i n d i c a t e d b y f l a s h i n g o f t h e L E D
corresponding to the processing program of
the ice cream selected.
•The desired cycle selection can take place
English
either at the beginning or during the
processing phase.
•Depending on the type of recipe and/or the
quantity prepared, every set of preservation
cycles combined with paddle speed enables
keeping gelato, Granita and sorbet or other
whipped products at the desired conditions.
•Pressing the button (12) several times causes
the selection LEDs of the various preservation
cycles to light up in sequence. If you switch
from the first (LED (12a) active) to the fourth
(LED (12d) active) preservation program, the
density of gelato increases gradually.
•Once you have selected the desired cycle, the
corresponding LED will flash for 3 seconds
and will become steadily lit, enabling the
selection.
•If you operate the knob that adjusts the paddle
speed, you will be able to adjust the density of
the preparation: to low speed corresponds a
higher density while at high speed you will
have an increased air intake and a smaller
density of the preparation. The speed and
selected cycle combination makes it possible
to obtain various preservation cycles in all
possible conditions.
VARIATION OF THE PRESERVATION CYCLE
You can always select a different preservation
cycle either during the active phase and during
the pause phase of the running cycle.
Repeatedly press button (12) until the LED that
corresponds to the desired cycle is activated.
The LED will flash for 3 seconds and become
steadily lit: The new preservation cycle is now
selected and it will be run for the set execution
times.
Should it become necessary to switch to a
preservation cycle associated to a different
program, you must enable the corresponding
program priorly, by pressing the button (11).
Once you have enabled the program, switch to
the preservation cycle by pressing buttons (2)
and (1) simultaneously for 3 seconds. The
machine will enable the preservation cycles
associated to the preset program.
SWITCHING FROM PRESERVATION PHASE
TO A PRODUCTION PROGRAM
With the preservation active, you can activate
an automatic program simply by selecting it by
pressing button (11). The LED corresponding to
the selected program will flash for 3 seconds
and become steadily lit; the machine will exit the
9