Remington MPS6017A Manual Para El Usuario página 10

MOWER iNFORMATiON
Attach Mulching Plug or Rear Bagger
Mulching Plug Installation
1. Remove key from mower.
2. Raise the hinged discharge guard on the
back of the mower (see Figure 9).
3. Insert mulching plug until the end of the
plug is flush with the discharge hole. (see
Figure 10).
Note: The mulching plug uses friction
to stay in place. It might be necessary to
wiggle the plug to fully install it and to
remove it.
4. Lower the hinged discharge guard.
Figure 9 - Discharge Guard
Figure 10 - Mulching Plug
Rear Bag Assembly
1. Insert wire frame into cloth bag (see figure
11 ). Make sure the wire fi'ame handle is
on top and the bag orientation shows the
Remington logo upright.
2. Pull cloth bag toward rectangular wire
fi'ame opening and attach cloth bag to wire
fi'ame with intergrated plastic clips. (see
Figure 12).
3. The plastic clips on the cloth bag attach
fi'om the inside of the rectangular wire
fi'ame. There are 2 clips on top, 1 on each
side and I on the bottom. (see Figure
13)
Figure 11 - Insert Into Wire Frame
Figure 13 - Attached Bag
Rear Bagger Installation
1. Raise the hinged discharge guard on the
back of the mower (see Figure 9).
2. Orient the rear bagger as shown in Figure
14.
3. Position the top fi'ont groove over the sup-
port rod (see Figure 14). Note: Slightly tilt
rear of bag upward to place the rear bagger
groove onto the support rod.
4. Lower rear of bag. Gravity and the weight
of the cut grass will hold the rear bagger
in place.
5. Release the hinged discharge guard.
Figure 14 - Rear Bagger
OPERATING MOWER
Safety Checks
A WARNING
Read and understand this own-
er's manual before operating
mower. Make certain you read
and understand all Safety Warn-
ings of this manual. Improper
use of this mower can result in
severe injury or death from fire,
electric shock, or body contact
with moving parts.
A WARNING
Do not modify this mower to
bypass the safety features.
These features are designed
to make it difficult for children
to operate the mower and to
protect the user.
WARNING
Do not insert the safety key
until you have completed all
of the Safety Checks and have
moved the mower to the area
being mowed.
Perform the following safety checks before
operating mower each time.
* Check that the blade is attached securely.
* Make sure all knobs, bolts, attachments,
and covers are in place and securely
attached.
. Inspect for any visible damage to the
blade or deck and remove any accu-
mulation of dirt, dust, or dried grass
clippings.
* Attach either the rear bagger, the mulch-
ing plug, or the optional side discharge
chute. See Attaching Muleing Plug or
Read Bagger.
, Set the mower to the desired cutting
height (see Adjustittg Wheel Height).
, Be sure the battery is fully charged.
, Befbre starting mower, push it to the
lawn area to be mowed.
Power Selection Dial
This Remington brand mower is designed to
operate from a rechargeable battery or l l0
volt outlet. To select the power source desired,
tk)llow the instructions below.
1. Locate the upper deck power selection dial
on the control board (see Figure 15).
2. Turn the dial to the selection desired (see
Figure 16).
Note: This mower is designed to operate using
the battery even if it is connected to a 110V
power supply. When the power selection dial
is turned to "Battery", the l l0V power input
is switched off.
Figure 15- Power Selection Dial
Figure 16 - Turn Dial
Figure 12 - Attach Clips to Frame
www.remingtonpowertools.com 10