Descargar Imprimir esta página

Onkyo T-403 Manual De Instrucciones página 3

Sintonizador de fm estéreo/am sintetizado por cuarzo

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 17
Precautions
Pe
ta end err
Mn RUE EOE
MSE at LT
as SEL ea
a Nn
1. Warranty
Card
The seria! number is written on the rear panel of this unit. Copy
the serial number and mode! number onto your warranty card
and keep it in a safe place.
2. Care
From time to time you should wipe off the front and rear panels
and the cabinet with soft cloth. For heavier dirt, dampen a soft
cloth in a weak solution of mild detergent and water, wring it
out dry, and wipe off the dirt. Following this, dry immediately
with a clean cloth. Do not use rough material, thinners, alcoho!
or other chemical solvents or cloths since these could damage
the finish or remove the panel lettering.
3.
Power
WARNING
BEFORE CONNECTING
THE UNIT TO AN AC OUTLET,
READ
THE FOLLOWING
SECTION
CAREFULLY.
@
Some models are designed for use only with the power supply
voltage of the region where they are sold.
European models:
AC230V, 50Hz
Canadian models:
AC120V, 60Hz
British & Australian models:
AC 240V, 50Hz
Worldwide models:
120 and 220V switchable,
50/60Hz
Supplied Accessories
Derr ia are en a eS Ee
ESS HIEE SEENESS aoa
|
Output signal cord x 1
fRI remote control cable
x 1
System connections
Voltage Selector (Rear Panel)
Worldwide models are equipped with a voltage selector to conform
with local power supplies. Be sure to set this switch to match the
voltage of the power supply in your area before plugging in the
unit. Voltage is changed by sliding the groove in the switch with
a screwdriver to the right or left. Confirm that the switch has been
moved all the way to the right or left before plugging in the unit.
Models without a voltage selector can only be used in areas where
the power supply is the same as that of the unit.
220V
at AC220V
220V ™
120V™
at AC120V
120V VU
Tuning Step Frequency
Switch
(Rear Panel)
Worldwide models are equipped with a switch that controls the
AM
(9kHz/10kHz)
and FM (50kHz/200kHz)
bands tuning steps.
Be sure to set this switch to match the tunig step frequency in your
area.
U.S.A:
Other area:
10 kHz/200 kHz
9 kHz/50 kHz
AM loop
antenna
x
1
T-shaped FM
antenna
x 1
Models for some areas
are equipped with a
screw-type FM antenna
terminal (75/300 ohms).
Indoor T-shaped
antenna
Do not connect both indoor and
outdoor FM antennas. If you decide to
install an outdoor antenna,
be sure to
disconnect the indoor feeder antenna.
Outdoor
FM antenna
AM
loop antenna
Outdoor AM
antenna
Ft REMOTE
CONTRO.
AC Power Supply
*
Tothe
QI]
remote contro}
jack Do not connect any pro-
duct to this jack that does not
have the ONKYO FRI mark.
*
The upper and lower
(RQ
remote control jacks have the
same function.
To Amplifier
When
connecting tuner output to the amplifier
be absolutely sure to connect the R (right) and L
(left) channels correctly
AM
foop antenna
assembly
Connect to the AM
antenna terminals
Remove
the vinyl tie and
take out the connection
line
Bend
in the reverse
direction
°
a
a. With the antenna
on
top of any stable surface
b. With the antenna
attached to a wail
instalation
hole
Mount on a wall, etc.

Publicidad

loading