Descargar Imprimir esta página

Onkyo T-403 Manual De Instrucciones página 4

Sintonizador de fm estéreo/am sintetizado por cuarzo

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 17
FM
Antenna
Connections
Use the T-shaped antenna if you live in an area where signal strength
of FM broadcasts is high. Connect the antenna to the FM 75 ohms
terminals and place the antenna on a wall or other surface in the
position in which reception is best. If signal strength is low in your
area, use a multi-element FM outdoor antenna.
Consult your
ONKYO
authorized service center about the right type of antenna
for your area.
NOTES:
. Do not connect both the indoor T-shaped antenna and an
outdoor FM antenna. If you decide to install an outdoor
antenna, be sure to disconnect the indoor T-shaped antenna.
. Do not use the same antenna for both FM and TV reception
since the FM and TV signals can interfere with each other.
If you must use
acommon FM/TV antenna, use a directional
linkage type splitter.
AM
Antenna
Connections
An AM loop antenna is included in the installation instructions bag.
Take out the connection line and connect it to the AM antenna
terminals. This loop antenna can be used placed on top of the tuner
or attached to a wall or other surface.
Try several positions to
determine which gives the best reception. Be sure the antenna is
not near a speaker, power cord, television set, VCR, or motorized
appliances. When using an external AM antenna, do not remove
the loop antenna; connect both antennas to the AM antenna ter-
minals.
RI Remote
Control Jack ( QI:
Remote
Interactive)
For remote control operation, connect this jack and any ONKYO
amplifier bearing the " (QI " mark using the remote control cable
included with this unit.(Station Up/Down buttons can be controlled
via the remote controller delivered with the amplifier.)
For more
details, see the user's manual for the amplifier.
NOTE:
The
FRI mark is ONKYO's own mark. Audio equipment with
this mark can be controlled through the amplifier with the
FRI mark, using remote control transmitter.
Do not connect
any product to this jack that does not have the ONKYO
FRI
mark. Doing so can damage your equipment.
Front panel
For more information about buttons or controls, turn to the page number listed in the [__].
Power Switch
(POWER)
[4]
Memory
Button (MEMORY)
[4]
ONE
VO
cuaaiz syntuesizeo rm STEREO/AM
FUNER AL
Muting/Mode Button (MUTE/MODE)
[4]
CLASSIFIED MEMORY PRESET
POWER
Tuning
Selector Buttons
( ~t
DOWN
TUNING
UP
» ) [4]
FM/AM
Selector Buttons (FM, AM)
[4]
Automatic
Precision
Reception
System
(FM Mode)
APR system is ONKYO's unique computer-controlied system.
APR system automatically sets the RF stage gain (Distance/
Local), auto stereo/mono reception modes to the proper settings
for the qualily of the broadcast currently being received. This
indicator changes each time the APR circuit switches between
the LOCAL/DX or AUTO/MONDO to show the current APR
setting. (APR system is effective for only FM reception.)
NOTE:
When
MUTE/MODE
button is not ON, the APR Mode se-
lection function does not operate, and the STEREO
MODE
indicator is forced to "MONO".
The "MONO" indicator lights up for FM monaural reception.
The RF MODE
will indicate LOCAL when sufficient signal
is received.
Display and indicators
Tuned Indicators
FM Stereo Indicator
Memory Indicator
*Sleep Indicator
bata
San
MEMORY
SLEEP
FM Muting On/Off
Indicator
APR System Indicators
Apa
RF
STEREC
MODE
MOSE
ae CE
Frequency Display
Classified Memory Display
Preset Station/Sleep Timer Display
*Sleep Indicator
This indicator comes on when the remote contro! unit with sleep
button is used to start the sleep function on an ONKYO amplifier
which
has been connected
using an
(QI remote control cable.
-3-

Publicidad

loading