Publicidad
Idiomas disponibles
Idiomas disponibles
Install
Ignitor
Battery
[] Unscrew
Ignitor Cap from
Control
Panel.
[] Place supplied
AA battery into the Ignitor
Slot with positive
pole facing
you.
[] Position the Cap and Spring over the AA
battery and tighten onto Control
Panel.
Main
Burners
Electrode
Check
Perform
this
Electrode
Check
with
the
assistance
of another
person.
This test will ensure that the Spark Electrode Tips
are properly positioned so your grill lights easily
and properly.
Spark Gap
Gas
Collector
Box
ctrode Tip
[]
Be
sure
all Control
Knobs
are
set
to
"OFF"
and
open
the
Grill
Lid.
[]
Have
your
assistant
stand
behind
to the
right
of the grill
and
look
toward
the
front
of the
grill bowl.
Never
put your
face
inside
the
Grill
Bowl.
[]
Press
the
Ignitor
Cap.
You
should
hear
a "clicking"
sound.
Your
assistant
should
see
a blue
spark
within
each
Gas
Collector
Box.
If a spark
is present
the
Electrode
Tips
are
properly
positioned.
[]
If no spark
is seen,
the
Spark
Gap
needs
to
be
adjusted
as
follows:
•
Using
an adjustable
wrench,
loosen
the
Inside Nut until the Gas Collector
Box can
be turned
upward.
•
If the
gap
between
the
Spark
Elec-
trode
Tip
and
Receiver
is more
than
3/16"
use
long
nose
pliers
to
gently
squeeze
the
Gas
Collector
Box
to
narrow
gap.
•
Return
the Gas Collector
Box to its
original
position,
secure
the
Inside
Nut
and try the Electrode
Check
again.
If no
"clicking"
sound
is heard:
•
AA
Battery
may
be installed
back-
wards.
•
Electric
wires
may be loose.
Remove
the AA
Battery
and inspect
the Ignitor
Junction
Box found
behind
the Control
Panel and reconnect
any loose wires.
Side Burner
and Rotisserie
Burner
Electrode
Check
[]
Open
side
burner
lid.
Remove
plastic
shipping
band
from
burner
and
pot
support.
[]
Turn
side
burner
Control
Knob
to
IGN
and
push
in.
Look
for
spark
between
tip
of
electrode
and
burner.
[]
Open
Grill
Lid.
Turn
rotisserie
burner
Control
Knob
to
IGN
and
push
in. Look
for
spark
between
tip
of electrode
and
burner.
[]
If you don't see a spark from side or rotisserie
burner
electrode,
adjust
gap between
electrode
and burner
surface
to 3/16
in.
,gnito -
Cap
Spring
AA Battery
Ignitor Slot
Install
Cooking
Components
[]
Place
the
Heat
Diffusers
on
lower
ledge
above
Burners.
[]
Place
Cooking
Grids
on
bowl
ledge.
[]
Place
the
Secondary
Cooking
Rack
into
the
slots
on
Grill
Bowl
Side
Panels.
Secondary
Cooking Rack
Cooking Grids
Heat
Slots for Secondary
Cooking Rack
Model141.16315800
When you have finished
assembling
your
grill be sure that
all screws
are tightened
for
safe operation
of your grill.
15
Failure to read and follow the Use and Care
Instructions could result in a fire or explosion
that could cause serious bodily injury, death or
property damage.
Publicidad
