Publicidad
Idiomas disponibles
Idiomas disponibles
GB
Specific Safety
Additional Safety Instructions for Pneumatic Power
Tools
Air under pressure can cause severe injury:
• Always shut off air supply, drain hose of air pressure and disconnect tool from air supply when
not in use, before changing accessories or when making repairs
• Never direct air at yourself or anyone else
• Whipping hoses can cause severe injury. Always check for damaged or loose hoses and fittings
• Whenever universal twist couplings (claw couplings) are used, lock pins should be installed and
whipcheck safety cables should be used to safeguard against possible hose-to-tool or hose-to-
hose connection failure
• Do not exceed the maximum air pressure stated on the tool
• Never carry an air tool by the hose
Additional Safety for Powered Screwdrivers
IMPORTANT: It is imperative to follow all national safety regulations concerning installation,
operation and maintenance.
• Do not allow anyone under the age of 18 years to use this tool, and ensure that operators are
qualified and familiar with the operating and safety instructions
• When using the tool, use safety equipment including safety glasses or shield, ear defenders, and
protective clothing including safety gloves. Wear a dust mask if the operation creates dust
• Use metal and voltage detectors to locate concealed electric, water or gas lines. Avoid touching
live components or conductors
• Ensure that the lighting is adequate
• Ensure that the bit/accessory is securely fixed in the Bit Holder (1). Insecure bits can be ejected
from the machine causing a hazard
• Before operation, check that there is sufficient clearance for the bit/accessory under the
workpiece
• Do not put excessive pressure on the tool, to do so would shorten its service life
• Bits/accessories may get hot during operation, allow to cool prior to handling them
• Never use your hands to remove sawdust, chips or waste close by the bit/accessory
• If you are interrupted when operating the tool, complete the process and switch off before
looking up
• Where possible, use clamps or a vice to hold your work
• Always disconnect the tool from the air supply before changing a bit/accessory
• Examine the Bit Holder regularly for signs of wear or damage. Have damaged parts repaired by a
qualified Silverline service centre
• Always wait until the tool has come to a complete stop before putting it down
• On completion of the work, disconnect the tool from the air source and remove the bit/accessory
from the machine
• Periodically check all nuts, bolts and other fixings and tighten where necessary
Product Familiarisation
1.
Bit Holder
2.
Trigger
3.
Direction Switch
4.
Air Inlet for Quick Connector
5.
EQ-4 EU Quick Connector
6.
EN-6 UK Quick Connector
Intended Use
Variable speed reversible Screwdriver powered by compressed air from a compressor. Uses
screwdriver bits and other compatible accessories with a hexagonal shaft diameter of 6.35mm
(1/4").
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition
• If any parts are missing or damaged, have such parts replaced before attempting to use this tool
6
Before Use
Fitting the quick connector
EQ-4
EU Type
EN-6
UK Type
Note: This tool is supplied with two different male airline quick connectors:
• EQ-4 – commonly used in Europe
• EN-6 – mainly used in the UK
• Please choose the connector that is compatible with the airline system you are using, and install
as outlined below:
1. Apply some PTFE tape (not included) to the screw threads of the Quick Connector (5 or 6). This
will help to maintain an air tight seal
Note: Apply PTFE tape tightly and in a clockwise direction, so it does not come off when the thread
is screwed into the tool.
2. Remove the protective plug from the air inlet
3. Using a spanner (not included) screw the quick connector into the air inlet located at the base of
the handle
4. Connect to airline, pressurise carefully, then carry out a leak check (e.g. by spraying small
amounts of soapy water on to the outside of the connectors)
• Air lines fitted with matching female quick connectors will now be a push fit to the tool
QUICK COUPLER
TO YOUR
NIPPLE
AIR TOOL
RECOIL HOSE
LEADER HOSE
Air supply connection
• This tool should be connected to a clean, dry air supply with inline oiler and water separator
• Do not allow supply pressure to exceed the maximum stated (see 'Specifications')
• Ensure that water is drained from air system daily
• Ensure that all parts of the system (hoses, couplers, etc.) are correctly rated for the air pressure to
be used
Setting tool power
• The tool speed/power can be adjusted by reducing/increasing the air supply pressure within the
range specified in 'Specifications'
• Whilst working with the tool, speed adjustments can be made via the trigger
Fitting bits and accessories
1. Disconnect the tool from the air supply
2. Insert the bit/accessory into the Bit Holder (1) by firmly pushing until it stops
3. Remove the bit/accessory by sliding the sleeve of the Bit Holder forward (away from the tool).
The bit should be ejected. If not, grip the bit and gently pull, whilst keeping the sleeve of the bit
holder held in the release position (forward)
WATER SEPARATION
NIPPLE
OILER
DRAIN DAILY
REGULATOR
AIR SUPPLY
Publicidad
