Publicidad
Idiomas disponibles
Idiomas disponibles
List of Materials
Parts included in your
Internal Blower Assembly
Remove parts from packages. Check that all parts
are included.
•
5 - 6 x 16 mm mounting screws
•
5 - 4.2 x 8 mm mounting screws
•
5-6xlnuts
•
5 - flat washers
•
1 - main motor support
•
1 - motor bracket
•
T-20 TORX®I- adapter (used for mounting screws)
Parts needed
•
1/2"(1.3 cm) UL listed or CSA approved wiring
conduit and connectors
°
1/2"(1.3 cm) UL listed or CSA approved strain relief
Tools required
°
Drill
•
1W' (3 cm) drill bit
°
3A6"(0.5 cm) drill bit
°
Pencil
°
Wire stripper or utility knife
°
Tape measure or ruler
°
Pliers
°
Caulking gun and weatherproof caulking
compound
°
Vent clamps
°
Jigsaw or keyhole saw
°
Flat-blade screwdriver
°
Metal snips
°
Phillips screwdriver
CAUTION
To reduce the risk of fire and electric shock, install this
blowers only with this Hood Insert models rated
maximum 7.4 A:
MODEL
RATING
EI30HI55K5
EI36HI55K5
EI48HI55K5
EIO6HIPIKS
3.7A
•
•
•
IMPORTANT
Observe all governing codes and ordinances.
It is the customer's responsibility:
To contact a quali!ed electrical installer.
To assure that the electrical installation is adequate
and in conformance with National Electrical Code,
ANSl/NFPA 70 -- latest edition*, or CSA Standards
C22.1-94, Canadian Electrical Code, Part 1 and
C22.2 No.0-M91 - latest edition** and all local codes
and ordinances.
If codes permit and a separate ground wire is used, it
is recommended that a quali!ed electrician determine
that the ground path is adequate.
Do not ground to a gas pipe.
Check with a quali!ed electrician if you are not sure
hood insert is properly grounded.
Do not have a fuse in the neutral or ground circuit.
IMPORTANT
°
A 120 volt, 60 Hz., AC only, 15-amp, fused
electricalcircuitisrequired,
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
°
Ifthehousehasaluminumwiring,
followthe
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
procedurebelow:
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
1.Connectasectionofsolidcopperwiretothe
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
pigtail leads,
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
2. Connectthealuminumwiringtotheadded
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
sectionofcopperwireusingspecialconnectors
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
and/ortoolsdesignedandULlistedforjoining
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
coppertoaluminum,
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
Followtheelectrical
connectormanufacturer'srecom-
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
mendedprocedure. Aluminum/copperconnection
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
mustconformwithlocalcodesandindustryaccepted
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
wiringpractices,
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
Wiresizesmustconformtotherequirementsofthe
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
NationalElectricalCodeANSl/NFPA70--
latest
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
edition*,orCSAStandardsC22.1-94,
Canadian
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
ElectricalCodePartl
andC22.2No.
0-M91 -latest
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
edition**andalllocalcodesandordinances,
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
AU.L-orC.S.A.-listedconduitconnectormustbe
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
providedateachendofthepowersupplyconduit(at
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
thehoodinsertandatthejunctionbox),
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
Copiesofthestandardslistedmaybeobtainedfrom:
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
* National Fire Protection Association Batterymarch Park
____________________
Publicidad
