Publicidad
Idiomas disponibles
Idiomas disponibles
CD DIGITAL OUT
(OPTICAL)
5.1 CH
VIDEO/AUX IN
INPUT
MD
LINE OUT
SUPER
WOOFER
Refer to the operating
instructions
of the connected
equipment
for details.
The connecting
cords are not supplied.
Obtain the necessary
connecting
cords.
Consult
your local Aiwa dealer for optional
equipment.
.s #
m.'!
w
q
'w .,.% ~., ., ,, .
.W
,,..
b. ..,,=
:,. ..-..,
=.
. . .
~,
-*,. 2!
w
8, ,+ #
r
wwklw,.#
*M*,-J !7! u ,'
r, m \*r% ,*
,&*=:- ..
VIDEO/AUX IN JACKS
This unit can input analog sound signals through these jacks.
Use a cable with RCA phono plugs to connect
audio equipment
(turntables,
LD players, VCRs, TV, MD players, etc.).
Connect the red plug to VIDEO/AUX
IN R jack, and the white plug
to VIDEO/AUX
IN L jack.
When
connecting
a turntable
Use an Aiwa turntable
equipped with a built-in equalizer amplifier.
This jack is recommended
to connect
with an MD player.
Use a cable with RCA phono plugs.
Connect
the red plug to MD R jack, and the white plug to MD L
jack.
When MD player is connected
to these jacks, no sound will be
output from LINE OUT jacks.
-.? -
r ,.-: :%-- ,.% m-:=:. . ,-:=
.,--:2:e2%$,. =-,.*:
---------
% -,. % -%? . . .. .J-:~.~% -%'w~, ' -: .-,:*, ?.9'. % ~:-.. % ~
LINE OUT JACKS
This unit can output analog sound signal through
these jacks.
Use a cable with RCA phono plugs to connect
audio equipment
with LINE
IN
(analog
input) jacks.
Connect
the red plug of a cable to LINE OUT R jack, and the
white plug to LINE OUT L jack.
m
Do not connect
an equipment
to LINE OUT and VIDEO/AUX
IN
simultaneously.
Otherwise,
noise is generated
and malfunction
occurs
b
a. = . . -,..}
L.s,q,.:
*,.,:,
:.,:<.:
.4.:...*
;.
.,,,,.
,*,T*..,,.,W
,,,,,.=
. .
.
.
.
,- =.',
. . .
,.,
.:!,"
..-%s.
-.s.
!-%
,W.,
.! 'r..,..,
.
.
.
CD DIGITAL OUT (OPTICAL) JACK
This unit can output CD digital sound signals through
this jack.
Use an optical cable to connect
digital audio equipment
(digital
amplifier,
DAT deck, MD recorder,
etc.).
Remove
the dust cap @ from CD DIGITAL
OUT (OPTICAL)
jack. Then, connect
an optical
cable plug to CD DIGITAL
OUT
(OPTICAL)
jack.
This unit can input
sound
signals
from the audio equipment
6
(DVD player, LD player, etc.) that contains a Dolby Digital decoder
~
with the 5.1 ch output terminals.
Refer to "CONNECTING
A DVD
z
PLAYER"
(page 27).
Q
1
To play equipment
connected
to VIDEO/AUX
IN jacks or MD
jacks, proceed
as follows.
1
Press VIDEO/AUX or MD.
2
To
play the equipment connected
to VIDEO/AUX:
press
VIDEO/AUX
once. "VIDEO
appears
on the display.
To play the equipment
connected
to MD: press MD. "MD
appears
on display.
Play the connected equipment.
To
change a source name in the display
When VIDEO/AUX
is pressed once, "VIDEO
is displayed initially.
It can be changed
to "AUX
or "TV.
With the power on, press POWER while pressing
VIDEO/AUX.
When the "5.1 ch IN" is displayed,
press VI DEO/AUX
again to
see the changed
source name.
Repeat the procedure
to select one of the names.
To
adjust the sound level of the external source
When the sound level of the external
source
is much higher or
much lower than that of other function sources, adjust it as follows.
1
Press VIDEO/AUX
or MD and play the equipment.
2
Press ++
or ~
so that the sound level becomes
the same
as that of other function
sources.
During recording,
the sound level can not be adjusted.
When the CD DIGITAL OUT (OPTICAL) jack is not being used
Attach the supplied
dust cap.
ENGLISH 26
Publicidad
