EINHELL TC-ST 18 Li Manual De Instrucciones Original página 21

Release the locking button for the On/Off switch
(2) and the ON/OFF switch (3).
6.2 Setting the pendulum action
(Fig. 13/Item 8)
The strength of the pendulum action of the saw
blade (12) can be adjusted using the selector
switch for pendulum action (8).
You can adjust the cutting speed, cutting perfor-
mance and appearance of the cut to the workpie-
ce you want to saw.
Set the selector switch for pendulum action (8) to
one of the following positions:
Position 0 = no pendulum action
Material: Rubber, ceramic, aluminium, steel
Please note: For fi ne and clean cuts, thin materi-
als (e.g. sheet steel) and hard materials.
Position 1 = small pendulum action
Material: Plastic, wood, aluminium
Please note: For hard materials.
Position 2 = medium pendulum action
Material: Wood
Position 3 = large pendulum action
Material: Wood
Please note: For soft materials and sawing along
the grain
The best combination of speed and pendulum
action depends on the material you want to saw.
We recommend you to make a trial cut on a waste
piece in order to check the ideal settings.
6.3 Making cuts
Caution!
•
Make sure that the On/Off switch (3) is not
depressed. Only then should you connect the
battery pack to the equipment.
•
Do not switch on the cordless jigsaw until you
have fitted a saw blade.
•
Use only saw blades that are in perfect con-
dition. Replace blunt, bent or cracked saw
blades immediately.
•
Place the saw foot flat on the workpiece you
want to saw. Switch on the jigsaw.
•
Allow the saw blade to accelerate until it
reaches full speed. Then slowly move the saw
blade along the cutting line. Exert only gentle
pressure on the saw blade as you do so.
•
When cutting metal, apply a suitable coolant
along the line you want to cut.
Anl_TC_ST_18_Li_SPK7.indb 21 Anl_TC_ST_18_Li_SPK7.indb 21
GB
6.4 Sawing out sections (Fig. 13)
Drill a 10 mm hole in the section you want to saw
out. Insert the saw blade into this hole and start to
saw out the required section.
6.5 Making parallel cuts (Fig. 14)
•
Mount the parallel stop and adjust as required
(see section 5.3).
•
Observe the instructions in section 6.3.
•
Cut as shown in Fig. 14.
6.6 Miter cuts (Fig. 9)
•
Set the angle on the soleplate (see section
5.4).
•
Observe the instructions in section 6.3.
•
Cut as shown in Fig. 9.
6.7 LED lamp (Fig. 1/Item 4)
The LED lamp (4) can be used in poor lighting
conditions to additionally illuminate the cutting
position. The LED light (4) will come on automati-
cally as soon as you press the On/Off switch (3).
6.8 Dust-blower function (Fig. 1 / Item 18)
A current of air can be activated to keep the cut-
ting line free of dust and chips.
•
To activate, slide the switch for the dust-
blower function (18) to the back.
•
To deactivate, slide the switch for the dust-
blower function (18) back to the front.
6.9 Using the sliding shoe (Fig. 15 / Item 19)
•
When using the tool on sensitive surfaces
you can mount the sliding shoe (19) on the
soleplate in order to stop the surface from
becoming scratched.
•
Hook the sliding shoe (19) in the soleplate (7)
at the front and press it up at the rear until it
latches on the soleplate (7).
•
To take off the sliding shoe (19), release it at
the rear of the soleplate and remove it at the
front.
- 21 -
04.07.2023 08:35:18 04.07.2023 08:35:18