Specific Safety Rules And Symbols - Metabo HPT CM 5SB Manual De Instrucciones

English
Investigate and take corrective action to eliminate the
cause of wheel binding.
h) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully re-enter the cut.
The wheel may bind, walk up or kickback if the power
tool is restarted in the workpiece.
i) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near the
line of cut and near the edge of the workpiece on both
sides of the wheel.
j) Use extra caution when making a "pocket cut" into
existing walls or other blind areas.
The protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kickback.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal parts
of the tool "live" and shock the operator.
2. ALWAYS wear ear protections.
Exposure to noise can cause hearing loss.
3. NEVER touch moving parts.
NEVER place your hands, fi ngers or other
body parts near the tool's moving parts.
4. NEVER operate without all guards in place.
NEVER operate this tool without all guards or safety
features in place and in proper working order. If
maintenance or servicing requires the removal of a
guard or safety feature, be sure to replace the guard
or safety feature before resuming operation of the tool.
5. Use right tool.
Don't force small tool or attachment to do the job of a
heavy-duty tool.
Don't use tool for purpose not intended —for example—
don't use circular saw for cutting tree limbs or logs.
6. NEVER use a power tool for applications other
than those specifi ed.
NEVER use a power tool for applications other than
those specifi ed in the Instruction Manual.
7. Handle tool correctly.
Operate the tool according to the instructions provided
herein. Do not drop or throw the tool. NEVER allow the
tool to be operated by children, individuals unfamiliar
with its operation or unauthorized personnel.
6
8. Keep all screws, bolts and covers tightly in place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
9. Do not use power tools if the plastic housing or
handle is cracked.
Cracks in the tool's housing or handle can lead to electric
shock. Such tools should not be used until repaired.
10. Blades and accessories must be securely
mounted to the tool.
Prevent potential injuries to youself or others. Blades,
cutting implements and accessories which have been
mounted to the tool should be secure and tight.
11. Keep motor air vent clean.
The tool's motor air vent must be kept clean so that
air can freely fl ow at all times. Check for dust build-up
frequently.
12. Operate power tools at the rated voltage.
Operate the power tool at voltages specifi ed on its
nameplate.
If using the power tool at a higher voltage than the rated
voltage, it will result in abnormally fast motor revolution
and may damage the unit and the motor may burn out.
13. NEVER use a tool which is defective or operating
abnormally.
If the tool appears to be operating unusually, making
strange noises, or otherwise appears defective, stop
using it immediately and arrange for repairs by a
metabo HPT authorized service center.
14. NEVER leave tool running unattended. Turn power
off .
Don't leave tool until it comes to a complete stop.
15. Carefully handle power tools.
Should a power tool be dropped or struck against hard
materials inadvertently, it may be deformed, cracked,
or damaged.
16. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon
tetrachloride, and alcohol may damage and crack
plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly dampened
with soapy water and dry thoroughly.
17. ALWAYS wear eye protection that meets the
requirement of the latest revision of ANSI
Standard Z87.1.
18. ALWAYS wear a mask or respirator to protect yourself
from dust or potentially harmful particles generated
during the operation.
19. Do NOT use any cutting tool other than a diamond
wheel.
Use the diamond wheel specifi ed in this manual.
20. Don't use it for cutting of metallic materials.
Diamond wheel may be broken or its service life may
be remarkably reduced when it is used for cutting of
metallic materials. Be sure not to use the wheel for
cutting of metals.