Publicidad
Idiomas disponibles
Idiomas disponibles
CARE & USE
Safety Tips
• Before opening gas cylinder valve, check the regulator for
tightness.
• When appliance is not in use, turn off controller and gas.
• Use long-handled barbecue utensils to avoid burns and splatters.
Use protective gloves when handling hot components.
• Maximum load for side shelf is 4.5 Kg.
• The grease cup (if equipped) must be inserted into appliance and
emptied after each use. Do not remove grease cup until appliance
has completely cooled.
• Be very careful when you open the lid, since hot steam may
escape.
• Be very careful when children, the elderly, or pets are nearby.
• If you notice grease or other hot material dripping from appliance
onto valve, hose or regulator, turn off gas supply at once.
Determine the cause, correct it, then clean and inspect valve,
hose, and regulator before continuing. Perform a leak test.
• Do not store objects or materials inside the appliance cart
enclosure that would block the flow of combustion air to the
underside of either the control panel or the firebox bowl.
• DO NOT disconnect or change gas container within 3m of an open
flame or other ignition source.
• This appliance can be used by persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards
involved
• Children shall not play with the appliance
• Cleaning and user maintenance shall not be made by children
without supervision
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
Cylinder Placement
Cylinders placed in the appliance shall have a maximum diameter of
340mm and maximum height, including regulator, of 400mm. Larger
cylinders are to be placed under side shelf or behind the barbecue
only. Cylinders placed on the ground shall not be placed under the
hot plate.
Regulator Requirements
A regulator must be used with this appliance. Use only gas regulator
supplied with your barbeque. If a regulator is not supplied then use
only regulator certified according to EN16129 (Flow rate max. 1.5
kg/h) and approved for your country and gas specified in Technical
Data.
Hose Requirements
Use only approved hose which is certified to appropriate EN
standard and does not exceed 1.5m length. For Finland, the hose
length shall not exceed 1.2m.Before each use, check to see if hoses
are cut or worn. Make sure hose is not kinked. Replace damaged
hoses before using appliance. Replace hose as required by national
requirements.
Ignitor Lighting
• Do not lean over grill while lighting.
1. Plug in AC power cord.
2. Open lid during lighting or re-lighting.
3. Turn ON gas at LP cylinder.
4. Press power button to turn on controller.
5. Turn knob to desired temperature.
6. Press and release knob to ignite grill. (To control only one side of the
grill, see instructions in Grill Operation.)
7. If ignition does not occur, clear error code by pressing and holding
power button to turn off grill. Wait 5 minutes and repeat the lighting
procedure.
WARNING
• Turn controls and gas cylinder off when not in use.
• Make sure that when connected hose does not touch any warm
surfaces.
CAUTION
If ignition does not occur, clear error code by pressing and holding power
button to turn off grill. Wait 5 minutes and repeat the lighting procedure.
If the burner does not ignite with the valve open, gas will continue to flow
out of the burner and could accidently ignite with risk of injury.
Leak Testing Valves, Hose and Regulator
Leak test before first use, at least once a year, and every time the cylinder is
changed or disconnected.
1. Turn appliance off. .
2. Be sure regulator is tightly connected to gas cylinder.
3. Turn on Gas. If you hear a rushing sound, turn gas off immediately.
There is a major leak at the connection. Correct before proceeding.
4. Brush soapy solution (mixture of half soap and half water) onto hose
connections.
5. If growing bubbles appear, there is a leak. Turn off gas at cylinder
immediately and check tightness of connections. If leak cannot be
stopped do not try to repair. Call for replacement parts.
6. Always turn off gas at cylinder after performing leak test.
IF APPLIANCE FAILS TO LIGHT
• Make sure gas is turned on at cylinder.
• Make sure there is gas in the cylinder.
• Does the ignitor make a sparking noise?Do not smoke during leak test.
1. If yes check for spark at burner.
2. If no spark check for damaged or loose wires.
• If wires are OK check for cracked or broken electrode,replace if needed.
• If wire or electrodes are covered by cooking residue, clean electrode tip
with alcohol wipe if needed.
• If needed replace wires.
• Check for loose wire connection at controller.
GB
4
C H AR BR O I L . EU
Publicidad
