Publicidad
Idiomas disponibles
Idiomas disponibles
• While your device is turned off, press and hold the "On/Off"button for 3 seconds.
• Press the "On/Off" button until "
• Adjust the operating sensitivity by using " " and " " buttons in the "
hysteresis negative menu.
• To save the settings and exit, press the "On / Off" button or wait 10 seconds until
the device turns off.
• Changes have been saved. Your Thermostat will be working with set operating
sensitivity when you open your device.
Factory settings reset: You can reset your Thermostat to its default factory settings. This
operation resets the mode temperature values, calibration setting, heating/coling modes
and hysteresis settings to factory setting. To reset your Thermostat to factory setting:
• While your device is turned off, press and hold the "On/Off"button for 3 seconds.
• Press the "On/Off" button until "
• While in the "
" menu, select the " " option by using " " or " " buttons and
press the "On/Off" button.
• Your device will be turned off and reset to factory settings.
Key lock: In the Thermostat there is a key lock function to avoid any unintended
contact. In order to unlock the Thermostat's key lock "Mode" button should be
pressed for 3 seconds. If buttons on Thermostat are not touched for 10 seconds, key
lock will be reactivated.
Day and hour settings
• While your Thermostat is on, keep pressing ''Weekly Program'' button for 3 seconds.
• At the first screen that appears ''Hour'' part will be blinking. You may set the
time with " " and " " buttons.
• After setting the time, ''Weekly Program'' button needs to be pressed once. For
minute setting, minute part will be blinking. You may set the minute with " "
and " " buttons.
• After setting the minute, ''Settings'' button needs to be pressed once to set the
day of the week.
• Monday has set as the first day of the week and indicated with number "1".
• Numbers indicates the following days respectively 2-Tuesday, 3- Wednesday,
4-Thursday, 5-Friday, 6-Saturday and 7-Sunday
• When setting is done you may exit by pressing for 3 seconds to "Settings" button.
G
Mode settings: Your Thermostat has 4 different modes. Two of them(Comfort and
Economy Mode) are preset modes. Other modes are manual mode and programming
mode. In preset modes, temperature values are based on the user's choices which
have been set in the beginning. Manual mode allows the Thermostat to operate within
the temperature which is required and set directly by user. Weekly Program mode
continues to work according to the weekly schedule determined by the user. In order to
change the temperature values of preset modes:
• Press and hold the "Setting" button for 3 seconds while your Thermostat is on.
• Comfort Mode temperature value will appear. You may adjust the temperature
value of Comfort Mode by pressing the " " and " " buttons.
• When setting is done, you may adjust the temperature value of Economy Mode
with the " " and " " buttons by pressing the "Mode" button.
• You may exit the setting screen by pressing the "Setting" button for 3 seconds.
• In order to change the manual mode temperature, press the " " or " " button
while in the main screen. The Thermostat will switch to Manual Mode once
pressed the " " or " " button.
• You may press the "Mode" button to switch to the other modes.
Weekly Program: You may set the operating schedule of your Thermostat with weekly
program mode. 7 different temperature values can be set for each day in weekly
programming. These values can be set in temperature adjustment screens '' P0-P6''.
• In order to set the weekly schedule, press and hold the "Weekly Program"
button for 3 seconds while your Thermostat is on. The "Hour, Minute and Day"
setting will appear. Press the "Settings" button until the "Weekly Program"
menu (P0) appears.
• Days of the week will be blinking on the screen. You can initiate the weekly
program setting if you wish to set the same schedule for every day of the week.
• Press the " " button once if you wish to set the same schedule for the
weekdays. First five days of week will be blinking on the screen.
• Press the " " button once more if you wish to set the same schedule only for the
weekend. Last two days of the week will be blinking on the screen.
• Press the " " button one more time if you wish to set a different schedule for
each day of the week. 1st day of the week will be blinking on the screen. You can
switch between the days by pressing the " " button. Press the " " button in
order to switch to the previous day.
• Press the "Weekly Program" button once to set a schedule. "P0" will be blinking
on the screen. Set the temperature value of "P0" by pressing the "Weekly
Program" button once more. The hour setting of "P0" cannot be changed since
it's factory setting.
• Press the "Weekly Program" button again. Day indicator will be blinking. If you
will not change the day, press the "Weekly Program" button again and switch to
the "P1" setting by pressing the " " button.
• First, hour setting will appear on the screen. Once you complete the hour setting,
adjust the minute setting by pressing the "Weekly Program" button. After the
minute setting, press the "Weekly Program" button to set the temperature value.
• Follow the same steps for other schedule settings.
• Once all changes made, press and hold the "Weekly Program" button for 3
seconds to save.
Note: In order to check the weekly schedule which has been set without making
any changes, press the "Weekly Program" button once while your Thermostat is on.
Press the " " and " " buttons to see the days, press the "Mode" button to see the
settings between "P0-P6".
Thermostat working logic
Heating Mode: Your thermostat takes the average room temperature of last
H
40 seconds as basis. If the room temperature goes above the hysteresis positive
temperature value you set, your Thermostat will stop the heating unit. If it goes below
the hysteresis negative temperature value, your Thermostat will start the heating unit.
Thus, it ensures that the room temperature remains within a certain range.
Cooling Mode: Your Thermostat takes the average room temperature of last
I
40 seconds as basis. If the room temperature goes above the hysteresis positive
temperature value you set, your Thermostat will start the cooling unit. If it goes below
the hysteresis negative temperature value, your Thermostat will stop the cooling unit.
Thus, it ensures that the room temperature remains within a certain range.
Frequently asked questions
Is my Thermostat compatible with my heating/cooling unit?
If your heating / cooling unit has on-off connections, your Thermostat is compatible.
You can find information about your heating / cooling unit from your heating / cooling
unit operating manual or from your heating / cooling unit service.
How will I connect my heating/cooling unit with my Receiver?
We recommend that the connection between the Receiver and heating/cooling unit
" menu appears.
" menu appears.
should be made by professionally qualified persons. 2x0.75 mm cable is sufficient for
the Receiver – heating/cooling unit connection.
"
Connect one end of the cable pair to the room thermostat connection terminals
stated in the user manual of your heating/cooling unit.
Connect the other end of the cable pair to COM and NO inputs of the terminal inside
the Receiver as shown in the "RECEIVER WIRING DIAGRAM" section.
The direction of the cable ends does not matter.
Warranty conditions
1. The warranty period starts from the invoice date and warranted against
manufacturing defects for 5 years.
2. Devices and apparatus are delivered to the customer in working condition in our
company. On-site commissioning is subject to a service fee.
3. The repair of the devices and apparatus covered by the warranty is carried out in
our company factory and should send by contracted transportation company. In
on-site services, the transportation and accommodation expenses of the service
personnel belong to the customer. The shift fee during transportation is added to
the service fee and collected in advance.
4. The maintenance of devices and apparatus is done in our company. For the
maintenance of the devices and apparatus, the round travel fares belongs to the
customer.
5. In case of malfunctioning of the devices and apparatus whose warranty period
continues, it is tested in our company whether the malfunction is caused by a
customer or manufacturer fault, and it is reported with a report issued by our
company.
6. In case of detection of manufacturer-induced errors of devices and apparatus
whose warranty period continues, the customer can request a replacement or
repair of the devices and apparatus at full expense by the manufacturer, unless
it's higher than the product's price.
7. In the event that the faults of the devices and apparatus whose warranty period
continues are determined as caused by the customer, all expenses would be
belong to the customer.
8. Customers should be aware of damages (if there is any) of product and warn
manufacturer since the day warranty duration starts.If customer do not warn
manufacturer with knowledge of damage, customer lose the rights of article 6.
9. Malfunctions resulting from the use of devices and apparatus contrary to the
matters stated in the User Manual are not covered by the warranty.
10. Devices and their apparatus are out of warranty if they are beaten, broken or
scratched by the customer.
11. Damages resulting from the use of devices and apparatus belonging to other
brands and models without the approval of the manufacturer are not covered by
the warranty.
12. Battery leakage and errors due to rust, oxidation and liquid contact by working in
acidic / humid environments are not covered by the warranty.
13. When the product is not used for a long period (more than 15 days), remove the
batteries. Otherwise, malfunctions that will occur are out of warranty.
14. Damages that may occur during the transportation of devices and apparatus are not
covered by the warranty. Customers can take a transportation insurance.
15. Damages caused by mains voltage / faulty electrical installation are not covered
by the warranty.
16. Devices and apparatuses are out of warranty for malfunctions caused by force
majeure such as fire, flood, earthquake etc.
17. All of the devices and apparatuses, including all their parts, are under the
warranty of our company.
18. In case of malfunction of the devices and apparatuses within the warranty
period, the time spent during repairment period is added to the warranty period.
The repair period of the product cannot exceed 20 working days. This period
starts from the date of notification to the service station of the malfunction
related to the product or, in the absence of a service station, to the seller, dealer,
agency, representative, importer or manufacturer of the product. Consumer can
report the problem by; phone, fax, e-mail, registered and reply paid letter or a
similar way. However, in case of a conflict, responsibility of prove is belong to
the customer. If the malfunction of the product is not repaired within 20 working
days, the manufacturer-producer or importer; has to allocate another product
with similar features to the use of the consumer until the repair of the product
is completed.
19. Although the consumer uses his/her repair rights.
- If the product breaks down for 4 times in a year or 6 times in warranty duration
and these problems effects main purpose of the product. (starting from delivery
time during warranty.)
- Exceeding the maximum time required for repair.
- In the event that the service station is not available, if it is determined that the
repair of the defect is not possible with the report prepared (in order) by one of
the seller, dealer, agency, representative, importer or manufacturer, a refund or
a price discount at the rate of defect can be requested.
20. The customer can make complaints and appeals to consumer courts or consumer
arbitration committees.
21. The warranty document must be kept by the customer during the warranty period.
If the document is lost, a second document will not be issued. In case of loss, repair
and replacement of devices and apparatus will be made for a fee.
7
Publicidad
