Publicidad
Idiomas disponibles
Idiomas disponibles
BLOCK CONNECTORS
3
CORNER CONNECTORS
1
Once all the needed connections have been made, peel the
liner o of the adhesive backer in incremental lengths and
a x the tape light to the mounting surface while pressing
firmly as the strip light is installed. NOTE: The tape light
may not adhere properly to unfinished wood or particle
board surfaces. Applying a coat of varnish or polyurethane
to the mounting surface or using insulated wire cable clips
(not included) may be needed to reinforce the holding
strength of the tape light adhesive.
Press power button to turn tape
ON and OFF. Hold power button
to adjust light level.
PROBLEM
LED strip does not light up.
1. Power/light switch is o .
LED strip adhesive is losing
1. It is mounted on unfinished wood or a particle board surface.
adhesion.
2. Surface is not wiped down.
Good Earth Lighting
- The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (6) years from the date of original purchase by the
®
consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment. We will repair or replace (at our option) the unit
in the original color and style if available, or in a similar color and style if the original item has been discontinued, without charge. Defective units must be properly packed and returned to the
manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a return authorization number and an address where to
ship your defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture product. The
manufacturer will not be liable for any other loss, damage, labor costs, or injury which is caused by the product. This limitation upon the liability of the manufacturer includes any loss, damage,
labor costs, or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (III) based upon theories of warranty, contract, negligence, strict liability, tort, or
otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty gives you specific rights, and you may also have other rights which vary from state to
state.
FCC STATEMENT: "This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or
modifications of this product is not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: --
Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit di erent from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.
FCC responsible party name : Good Earth Lighting Inc. Address: 1400 E Business Center Drive, STE 108 Mount Prospect, IL 60056 USA. Telephone number: 1-800-291-8838
Please visit our website at: https://goodearthlighting.com/contact-us
Need Help?
or call the Customer Care Center 1-800-291-8838, 8:30 a.m.-5 p.m.,
CST, Monday-Friday.
Printed in Thailand
Align the polarity symbols
Align the polarity symbols
ATTACHING TAPE LIGHT TO SURFACE
FUNCTION CONTROLLER
TROUBLESHOOTING GUIDE
BEFORE DOING ANY WORK ON THE FIXTURE, UNPLUG THE
DANGER!
POWER CORD FROM THE ELECTRICAL OUTLET!
POSSIBLE CAUSE
6-YEAR LIMITED WARRANTY
Line up the LED tape light sections being connected and
3
make sure the "+" signs are all facing the same side. Once
the latches are open, seat the LED tape light sections on
top of the contacts. One at a time, close down on the
latches until they are locked. The contacts will pierce the
contact plates in the LED tape light to complete the
connection.
Do not reposition tape light once it is mounted.
Doing so will reduce the adhesiveness of the
tape backing.
Once in place, allow the
tape adhesive to cure
for 24 hours before use.
Press button to toggle through the di erent
CCT colors:
2700K, 3000K, 3500K, 4500K, 6500K
1. Turn switch on.
1. Mount with brackets and screws (not included).
2. Clean surface and reapply new layer of double-sided tape such as 3M VHB (not included).
Good Earth Lighting
Prospect, IL 60056
Good Earth Lighting
© 2022 Good Earth Lighting, Inc.REV11.22
The corner connectors are flexible and
can be used either for splicing or
navigating tight corners that the LED
tape light is unable to form to. DO NOT
CUT the flexible cord.
2
Attach power cord to tape
light. Plug in to electrical
outlet.
CORRECTIVE ACTION
1400 East Business Center Drive, Ste. 108 Mount
®
®
is a registered trademark of Good Earth Lighting, Inc.
2
Publicidad
