Good Earth Lighting AC1373-RWF-06LFW-G Instrucciones

Luz LED con cinta autoadhesiva
Function controller
Contrôleur de fonctions
Mounting screw (X5)
Controlador de funciones
Vis de montage (X5)
Tornillo de montaje (X5)
ATTENTION
● No parts are serviceable on this product. DO NOT
alter anything in this kit other than the tape light
length.
● For INDOOR locations only.
● For electrical requirements, see back of driver
label.
● This tape light is NOT expandable. Additional LED
tape light lengths CANNOT be added.
● Use only insulated staples or plastic ties (not
included) to secure the cords.
● DO NOT use with an extension cord. Use a power
strip with integral over current protection to
supply power to the fixture. NEVER use power
strip unless the plug can be fully inserted.
● LEDs gradually emit less light over their lifetime.
The LED tape light can only be cut on the "cut symbols,"
which are marked every 4 inches (10,2 cm), allowing for
cornering and/or custom installs.
ADDITIONAL TAPE LIGHT LENGTHS
CANNOT BE ADDED.
Attaching the connector to the LED Tape light
1
To connect the LED tape light to the connector, line up the arrow
located on the leading end of the LED tape light with the arrow
molded on the connector and insert.
Attaching Tape Light to Surface
2
Select a location for the LED tape light and mark it. Verify that
the USB cord reaches the nearest USB port. Thoroughly clean
the mounting surface with rubbing alcohol and allow it to dry.
DO NOT PLUG THE USB CORD INTO THE POWER SOURCE
UNTIL INSTALLATION IS COMPLETE. Remove the backing
liner carefully so as to not accidentally peel away the
mounting glue of the LED tape light. Place the LED tape light
in the desired position. Carefully apply pressure to the entire
length of the LED tape light to ensure proper adhesion.
Do not reposition tape light once it is mounted.
Doing so will reduce the adhesiveness of the
tape backing.
LED tape light
Ruban lumineux à LED
Clear Mounting Clips (X5)
Pinces de montage transparentes (X5)
Clips de montaje transparentes (X5)
ENGLISH INSTRUCTIONS
SAFETY INFORMATION
THIS LIGHT IS CUTTABLE BUT NON-LINKABLE
WARNING
● DO NOT INSTALL WHILE UNIT IS PLUGGED IN. DO
NOT plug the USB cord into the power source until
installation is complete
● DO NOT touch, operate, or install fixture while in
contact with water. Not intended for illumination
of aquariums.
● DO NOT look directly at lighted LEDs for any
length of time.
● DO NOT USE THIS FIXTURE WITH A DIMMING
CIRCUIT. If dimmer controls are present, remove
and replace.
ADJUSTING TAPE LENGTHS
NOTE: DO NOT cut the LED
tape light strips anywhere
other than the "cut
symbol." Doing so will
damage the tape light.
INSTALLATION
Once in place, allow the
tape adhesive to cure
for 24 hours before use.
6 FT USB WIFI RGBW TAPE LIGHT (Page 1)
Ruban d'éclairage USB WIFI RVBB de 1,83 M (Page 2)
LUZ CON CINTA AUTOADHESIVA USB WIFI RVNB DE 1,83 M (Página 4)
Model / Modèle / Modelo #: AC1373-RWF-06LFW-G
Plastic Cord Clip
Pince de fixation du cordon en plastique
Clip de plástico para el cable
Red adhesive tape
Ruban adhésif rouge
Cinta adhesiva roja
CAUTION
●
If unfamiliar with electrical installations, contact
a qualified electrician to install.
●
NOT intended for recessed installation in ceilings
or so ts. DO NOT run ANY cords behind walls,
ceilings, so ts, cabinets or a similar permanent
structure where it may be inaccessible for
examination.
●
Tape light must be fully uncoiled for proper
operation, and to prevent overheating.
●
Lights may be installed inside of an enclosure,
such as a cabinet, ONLY when the POWER
ADAPTER is located outside of the enclosure.
●
DO NOT mount over sinks or stoves.
CUT
SYMBOL
3
Using the provided red adhesive
tape, peel o white paper and
attach to the back of the function
controller. Remove the red lining
from the tape and press onto
surface.
Required / Nécessaire /Se necesita
Safety glasses
Lunettes de protection
Lentes de seguridad
Scissors
Ciseauxlentes
Tijeras