Descargar Imprimir esta página

Craftsman WEEDWACKER 316.795860 Manual Del Propietário página 5

Ocultar thumbs Ver también para WEEDWACKER 316.795860:

Publicidad

Idiomas disponibles

Idiomas disponibles

APPLICATIONS
Asatrimmer:
• Cutting grass and light weeds
Edging
Decorative
trimming around trees, fences, etc.
Asabrushcutter:
Cutting weeds and light brush ofup to1/2 inch indiameter
Other optional accessories
may b eused w ith this unit.
D-Handle
Shaft Grip
On/Off
Control
Shoulder
Strap
Clip
Spark Plug
Muffler
Starter
Rope
Grip
Fuel Cap
Convertible
TM
Coupler
Air Filter
Cover
Throttle
Control
Shaft Housing
\
Barrier
Bar
Brush
Blade
Blade Shield
/
Shield
Mount
Hassle Free ®
Cutting
Head
Line Cutting
Blade
Primer Bulb
Head
Shield
iNSTALL AND ADJUST THE D-HANDLE
1.
Remove the screws and
Screw
(4).
bottom clamp piece that were
installed on the D-handle for
shipping.
2.
Place the D-handle over the
shaft housing and onto the
bottom clamp (Fig. 1). Place
it a minimum of 6 inches
(15.24 cm) from the end of
the shaft grip.
3.
Start the screws with a large
Flat-head or T-25 Torx
screwdriver. Do not tighten
Minimum 6 in.
(15.24 cm)
Barrier
Bar
/
Bottom
Clamp
Fig. 1
until making the handle adjustment.
4.
If it was pre-installed,
loosen the screws on the D-handle just enough to
move it.
5.
While holding the unit in the operating position (Fig. 17), move the D-handle
to the location that provides the best grip.
6.
Tighten the clamp screws evenly until the D-handle is secure.
NOTE:
Make sure the barrier bar will point toward the operator's
body
when the unit is held in the operating
position.
OPERATING
THE CONVERTIBLE
TM
COUPLER SYSTEM
_
ARNING:
Before using any attachment,
read and understand
the manual that came with the attachment.
Follow all safety
information
contained within.
The Convertible
TM
coupler system enables the use of these optional attachments.
• Edger
• Cultivator
• Turbo Blower
• Brushcutter
5
• Pole Saw
• Hedge Trimmer
INSTALLING THE TRIMMER ATTACHMENT
OR OTHER ATTACHMENT
I A
I WARNING:
To avoid serious personal injury and damage to the I
_
unit, shut the unit off before removing or installing attachments.
!_!CAUTION:Beforeoperatingtheunit,
besurethattherelease
I
button is fully snapped into the primary hole, and that the knob is
securely tightened.
NOTE:
1.
2.
To make installing or
Primary Hole
removing the attachment
_,
easier, place the unit on
the ground or on a work
bench.
Turn knob counterclockwise--_"
'____t__,
rq
r------_
to loosen (Fig. 3).
While firmly holding the
attachment,
push it straight
Upper Shaft
into the Convertible
TM
coupler until the release
button snaps firmly into the
primary hole (Fig. 2).
NOTE:
Aligning the release
button with the guide
recess will help
installation
(Fig. 4).
3.
Turn the knob clockwise to
tighten (Fig. 3).
For decorative
edging with the line
head trimmer attachment
or other
attachment,
lock the release
button of the attachment
into the
90 ° hole (Fig. 3).
Housing
LowerShaft
Housing
90 ° Edging
Hole
(Trimmer Only)
Fig. 2

Publicidad

loading