Publicidad
D.يAssemblyيofيtheيbabyيhighchair
You will need the Allen wrench (12). Perform assembly on soft surface that will not damage surface of elements.
Start from assembling the leg (1) with the cross-bar (4). Notice that there are protruding pins in the cross-bar. Gently
adjust the protruding element with the first orifice from the bottom. Look at the figure A and adjust the cross-bar in the
way enabling you to insert the cylinder nut (11) into the orifice on the side element surface. Insert the bolt (13) into the
orifice in the leg and tighten it through the cross-bar into the nut. Pay attention that the bolt must match the nut. Then
use the Allen wrench (12) to tighten the bolt.
Repeat the aforesaid steps with the next cross-bar (4) by fixing it to the same leg (1). Tighten another leg (2) to the
structure consisting of two cross-bars and one leg. At this and subsequent stages we suggest to leave the leg 2 slightly
loosened in order to enable assembly of next elements inside the chair. The emerging structure must look as shown at
the figure B.
Tighten the oblong bar (3) with the bolts (10) to the emerging structure from both sides at leg half-height (fig. C). The
structure shall be as shown as the figure D.
Then gently insert the backrest (5) into the sockets located at the very top of the legs from their inside. Vertically insert
the rectangular nut (from the right side/ leg 1) (15) to the already inserted backrest. Insert the bolt (9) into the orifice
in the leg and then tighten through the backrest into the nut (figure E). Pay attention that the bolt must match the nut.
Repeat this step at another side of the backrest, however remember not to tighten the bolt to leave play for assembly
of other elements. The figure F shows the backrest fixed to the structure.
Gently insert the narrow backrest board (14) into the sockets located beneath the backrest at the legs from inside.
Insert the vertically rectangular nut (from the right side/ leg 1) (15) to the already inserted narrow board. Insert the bolt
(9) into the orifice in the leg and then tighten through the board into the nut (figure G). Pay attention that the bolt must
match the nut. Repeat this step at another side of the narrow board, however remember not to tighten the bolt to leave
play for assembly of other elements. The figure H shows the assembled elements.
Place the bumper bar with a safety harness (8) in the sockets at the inner side of the legs. Then place the small board
(6) in the position 9 (fig. P) or 10 (fig. R) depending on the size of the child, and the large board (7) in position 3/4/5
(figures I). Figure J shows the distance from the edges of the side legs in which you can insert the board. Tighten firmly
all bolts in the chair. Insert belts into the narrow orifices in the small board (6) and the narrow backrest board (14). After
sliding the belt through the orifice straighten the stitching in the way arranging the belt and the stitching perpendicularly
to each other (figure N). Make sure the belts are not twisted at any point (figure M).
Then attach the fitting (17) to the two remaining orifices located at the legs from outside. Tighten the fitting to the chair
with the bolts (18) using the Allen wrench (12) (figure K).
After pressing side red buttons insert the tray (16) into the fittings (figure L). The tray is mounted correctly, if, after
being removed, you will hear the characteristic sound of the buttons going forward.
After reassuring yourself all elements are mounted within the structure and there is nothing left, firmly tighten all bolts
in the chair.
Cushion assembly*:
You will find two cushions in the set. The cushion with a hole is intended for the seat (19), while the second cushion is
intended for the backrest (20). To attach the cushion to the seat, slide the crotch strap through the hole in the cushion,
disconnect the straps on the cushion and then slide it through the chair. Reconnect the belts under the seat with Velcro
straps. To attach the cushion to the backrest, disconnect the straps on the cushion and then slide them through the
chair element. Reconnect the straps with Velcro (Figure O).
E. Belt adjustment
The belts are adjusted by means of plastic clamps.يAdjustيbeltيlengthيtoيbaby'sيsize.يAttention!يTheيbeltsيprotectيaيbabyي
against falling from the chair, must stabilize baby position, however they must not be too tight and uncomfortable.
24
Publicidad
