Bosch HDS252U Instrucciones De Instalación página 5

4. Connect Electric
Ranges are dual rated for use on either !20/240 VAC or !20/208
VAC, See table for power ratings and circuit breaker sizes based
upon the supply voltage for each mode (See chart below).
VOLTS HZ RATING CIRCUIT
A,C. KW BREAKER
1!20/240 60 !2.! 30 ANPS
!20/208 60 9.! 25 ANPS
Place strain relief in knockout below terminal block (See Figure 4
below). Feed range cord through hole and strain relief up to
terminal block. Allow for slack in the cord between the strain
releif and terminal block. Once cord length/slack has been
adjusted, attach strain relief per instructrions included with strain
reliefi Connect wiring as described below and on next page.
CAUTION:
make certain that gas shutoff valve and all
burner controls are in OFF position before beginning.
TO PREVENT ELECTRICAL SHOCKr THE GROUNDING PRONG
SHOULD NO% UNDER ANY CIRCUMSTANCESv BE CUT OR RE-
MOVED. IT HUST BE PLUGGEDINTO A NATCHTNGGROUNDING
TYPE RECEPTACLE AND CONNECTEDTO A CORRECTLYPOLAR-
IZED 240=VOLT CIRCUIT. A separate circuit is recommended
which is in compliance with the NEC.
If there is any doubt as to whether the wall receptacle is prop-
edy grounded, have it checked by a qualified electddan.
This appliance may be connected to the power supply by installing
flexible conduit or a power cord set. The electrical rating of the
power cord set (not su pplied) must be 240 volt, 30 amperes. The
power cord set shall be marked "For Use with Ranges."
The power supply shall be connected to the range terminal block
compartment located near the bottom of the back panel (See
Figure 4,at dght). It is accessible by removing the terminal block
cover.
Gas Conn_n /
Electric Connection
(found behind terminal
b!ock
_ Range
Cord Through
Strain Relief in
Knockout
Pane?_ler_
Figure 4
i..,e,ef
pro ided, ith yo r,a,,g
.,u,tbe proporJy i.,,to,ed, S
Electrical Connection Procedures
Refer to Figures 5-10 ( below and next page) for further explanation.
WARNING
CONSULT YOUR INSTRUCTIONS FOR 'ELECTRICAL CONNECTION PROCEDURES'. COPPER WIRE MUST BE USED
FOR CONNECTION TO THE TERMINAL BLOCK. WHEN POWER SUPPLY CORD KIT IS USED TO CONNECT RANGE TO
THE POWER SUPPLY, USE ONLY CORD KITS RATED 120/240 VOLTS MINIMUM AND MARKED FOR USE WITH RANGES.
REFER TO INSTALLATION INSTRUCTIONS FOR PROPER CORD KIT AMPERAGE RATING, RISK OF FIRE OR
ELECTRICAL SHOCK HAY BE INCURRED IF AN INCORRECT SIZE RANGE CORD KIT IS USED, THE INSTALLATION
INSTRUCTIONS ARE NOT FOLLOWED, OR THE STRAIN RELIEF BRACKET IS DISCARDED.
RISK OF ELECTRIC SHOCK FRAME GROUNDED TO NEUTRAL OF APPLIANCE THROUGH A LINK GROUNDING
THROUGH THE NEUTRAL CONDUCTOR IS PROHIBITED FOR NEW BRANCH-CIRCUIT INSTALLATIONS, (1996 NEC)
MOBILE HOMES AND RECREATIONAL VEHICLES, OR IN AN AREA WHERE LOCAL CODES PROHIBIT GROUNDING
THROUGH NEUTRAL CONDUCTOR. FOR INSTALLATIONS WHERE GROUNDING THROUGH THE NEUTRAL CONDUC-
TOR IS PROHIBITED:
(1) DISCONNECT THE LINK FROM THE NEUTRAL.
(2) USE GROUNDING TERMINAL OR LEAD TO GROUND UNIT: AND
(3) CONNECT NEUTRAL TERMINAL OR LEAD TO BRANCH CIRCUIT NEUTRAL IN USUAL MANNER
(WHEN THE APPLIANCE IS CONNECTED BY MEANS OF A CORD KIT, USE 4 CONDUCTOR
CORD FOR THIS PURPOSE).
Center or white wire
must always be
attached to the
central terminal on
block.
All screw and nut
connections must be
t_ght.
3-WmRE HOOK UP
4-WIRE HOOK UP
Remove ground
strap from terminal
block. Install with
care, the green
ground wire as
shown at left Attach
ground wire and
strap with screw
provided with strap.
Figure 5
Page 4