GGP ITALY ES 414 Manual De Instrucciones página 19

EN
STANDARDS OF USE
For instructions regarding the engine and the battery (if sup-
plied), read the relevant manuals.
1. FINISH ASSEMBLY
NOTE – The machine can be supplied with some of the com-
ponents already fitted.
1.1a
"A" type handle – without height adjustment - Attach
the bottom of the handle (1) to the holes on the side of the chas-
sis. Secure it using the nuts and bolts supplied (2). Fit the top of
the handle (3) using the nuts and bolts (4) provided, ensuring that
the spiral (5) of the starter cable is positioned correctly.
On some models: connect the engine brake cable (6) by attach-
ing the wire terminal (7) to the hole on the control lever (8).
Fasten the cable support (6a) to the handle using the nuts and
bolts (9) as shown.
Attach the control cables using the clamps (10).
1.1b
"B" type handle - with height adjustment -
Return the bottom of the fitted handle (1) to its working position
and lock it in place using the bottom knobs (2). Make sure that the
two pins (3) stay inside their holes (4).
Fit the top of the handle (5) using the nuts and bolts (6) provided,
ensuring that the spiral (7) of the starter cable is positioned cor-
rectly.
On some models: connect the engine brake cable (8) by attach-
ing the wire terminal (9) to the hole on the control lever (10).
Fasten the cable support (8a) to the handle using the nuts and
bolts (11) as shown.
Attach the control cables using the clamps (12).
By loosening the knobs (2) the handle can be set at two different
heights.
1.2
Assemble the dashboard (1) following the steps shown.
1.3a
For a rigid grass-catcher:
Carefully detach the plate (1) and washers (2) from the top of the
grass-catcher (3). Eliminate the washers (2) and fit the plate (1)
onto the top of the grass-catcher (3) so that it clicks into place.
Assemble the two parts of the grass-catcher (3) and (4), making
sure that the hooks are fully locked into place and fasten them
using the screws supplied (5).
1.3b
For a plastic and cloth grass-catcher:
Carefully detach the plate (11) and washers (12) from the top of
the grass-catcher (13). Fit the plate (11) onto the top of the grass-
catcher (13) so that it clicks into place. With the plastic part (13)
upside-down, fasten the frame (15) using the screws (16) and
washers (12). Insert the frame (15) in the grass-catcher (17) and
attach the plastic bars (18) using a screwdriver, as shown in the
drawing. Fit the edge of the cloth (19) right into the groove of the
plastic part (13), starting 5-7 mm from the ends.
1.4
On models with an electric starter, connect the battery
cable to the lawnmower's general cable connection.
2. DESCRIPTION OF CONTROLS
2.1
The throttle (where fitted) is controlled by the lever (1) and
positioned as shown on the relative plate. Some models have a
fixed speed, and therefore no need of a throttle.
2.2
The blade brake is controlled by the lever (1), which
should be held against the handle when starting and using the
lawnmower. The engine stops when the lever is released.
2.3
In the power-driven models, pull the lever (1) towards the
handle for forward movement. The lawn-mower stops moving for-
ward when the lever is released.
2.4
The cutting height is adjusted using the levers (1).
On some models, remove the brake cover (2) and unscrew the pin
(3) using the wrench (4) provided; fit the wheels into the required
hole (5) and fully tighten the pin (3) using the wrench (4). The four
wheels must be at the same height. MAKE THIS ADJUSTMENT
ONLY WHEN THE BLADE IS STOPPED.
3. GRASS CUTTING
3.1
Lift the stone-guard and attach the grass-catcher (1) cor-
rectly as shown in the drawing.
3.2
To start the engine, follow the instructions in the engine
booklet and then pull the blade brake lever (1) towards the handle
and give a sharp pull on the starter cable knob (2). For models
with an electric starter, turn the starter key (3).
3.3
The lawn will look better if it is always cut to the same
height and in alternate directions.
3.4
When you have finishing mowing, release the brake lever
(1) and disconnect the spark plug cap (2). Remove the starter key
(3) (where fitted). WAIT FOR THE BLADE TO STOP before carry-
ing out any type of work on the machine.
4. ROUTINE MAINTENANCE
IMPORTANT – Regular, careful maintenance is essential for
keeping the safety level and original performance of the
machine unchanged in time.
Store the lawnmower in a dry place.
1) Wear strong working gloves during any cleaning, maintenance
or adjustment operation on the machine.
2) Carefully clean the machines with water after each cut; remove
the grass debris and mud accumulated inside the chassis to
avoid their drying and thus making the next start-up difficult.
3) The paintwork on the inside of the chassis may peel off in time
due to the abrasive action of the cut grass; in this case, inter-
vene promptly by touching up the paintwork using a rustproof
paint to prevent the formation of rust that would lead to corro-
sion of the metal.
4) Should it be necessary to access the lower part, only tilt the
machine from the side shown in the engine handbook; follow-
ing the relative instructions.
5) Do not drip petrol onto the plastic parts of the motor or the
machine to prevent damaging them and remove all traces of
spilt petrol immediately. The warranty does not cover damage
to plastic parts caused by petrol.
4.1
All operations on the blade should be carried out at a spe-
cialized centre.
Note for specialized centres: Reassemble the blade (2) as
shown in the drawing and tighten the central screw (1) using a
torque wrench set to 50-60 Nm.
4.2
In the power-driven models, regulate the adjuster (1) so
that the wire (2) is slightly loose, with the lever (3) at rest
4.3
To recharge a flat battery, connect to the battery charger
(1) following the instructions in the battery maintenance hand-
book.
Do not connect the battery charger directly to the engine terminal.
It is not possible to start the engine using the battery charger as
a power source, as it may get damaged.
If the machine is to remain inactive for a long period, disconnect
the battery leads after making sure that the battery is fully
charged.
Should you have any doubts or problems, do not hesitate to con-
tact your nearest Service Centre or your Dealer.
17