Publicidad
Idiomas disponibles
Idiomas disponibles
1600A01UV3.qxp_GKS18-25 4/27/20 8:12 AM Page 17
remove the cover A from the side of the
handle, by turning it 1/4 turn counter-
clockwise (Fig. 9a or 9b).
-
If the tool is already equipped with the
connectivity module, remove the battery
B, but do not remove the connectivity
module C.
-
If the connectivity module is installed for
the first time, remove the plastic
placeholder D from the connectivity
module compartment, and place the
connectivity
compartment
orientation (Fig. 9b). Note: Store the
placeholder D in a safe place. Reinsert
the
communications module is removed.
-
Next place new battery B on the top of
the connectivity module with the "+"
polarity facing up (Fig. 9a).
-
Place the cover A over the battery and
turn it ¼-turn clockwise to lock using a
flat screwdriver or a coin.
USING THE 'BOSCH TOOLBOx' APP
The
'Bosch
downloaded from the App Store or Google
Play.
Install the 'Bosch Toolbox' app on your
mobile device or make sure you are running
the latest version of the app.
Launch the 'Bosch Toolbox' app on your
mobile device and click on "My Tools"
icon/tile. Follow the app directions to pair
the tool with the mobile device.
BENEFITS SUMMARY OF
CONNECTIVITY MODULE AND APP
When used with the connectivity module,
the 'Bosch Toolbox' app will allow for the
following with the tool:
–
Registration and personalisation
–
Status check and warning messages
–
General information and settings
–
Adjusting the speed levels
The help button on the app explains
the features of the app.
The info button on the app displays
tool information and specifications.
The alerts button displays any alerts
received from the tool.
Lock-off Release Buttons
The Lock-off release buttons are designed
ind Quality Products Online at:
Operating Instructions
module
C
observing
placeholder
again
Toolbox'
app
GlobalTestSupply
www.
to prevent accidental starts. To operate,
press the release button 1 with your thumb
on either side of handle to disengage the
lock, then pull the trigger 2 (Fig. 1). When
the trigger is released the button will
engage the safety switch automatically, and
the trigger will no longer operate.
Switch
When starting the tool, hold it with both
hands. The torque from the motor can
in
the
cause the tool to twist.
correct
To turn tool on, press the lock-off release
button 1 with your thumb on either side of
handle to disengage the lock, then pull the
if
the
trigger 2 (Fig. 1). To turn the tool "OFF",
release the trigger switch, which is spring
loaded and will return to the off position
automatically.
Your saw should be running at full speed
BEFORE starting the cut, and turned off
only AFTER completing the cut. To increase
switch life, do not turn switch on and off
while cutting.
All Cuts
can
be
with the free movement of the lower
guard.
released, be aware of the nec es sary time
it takes for the blade to come to a com -
plete stop during coast down. Do not
allow the saw to brush against your leg or
side, since the lower guard is retractable,
it could catch on your clothing and expose
the blade. Be aware of the necessary
blade ex posures that exist in both the
upper and lower guard areas.
Always hold the saw handle with one hand
and the auxiliary handle or housing with
the other.
Always make sure saw foot rests on portion
of work surface that does not drop off.
Maintain a firm grip and operate the switch
with a decisive action. Never force the saw.
Use light and continuous pressure.
When cutting is interrupted, to resume
cutting: squeeze the trigger and allow the
blade to reach full speed, re-enter the cut
slowly and resume cutting.
Always be sure either
hand does not interfere
After completing a cut
and the trigger has been
.com
sales@GlobalTestSupply.com
17
Publicidad
