Garmin GMI 20 Instrucciones De Instalación página 3

Item Description Notes
Device bracket This half of the bracket connects to the device
using the included threaded rods and lock nuts.
Surface bracket This half of the bracket connects to the
mounting surface using either the included
screws or other hardware appropriate for the
mounting surface (not included).
Hex screws These screws secure the two halves of the
bracket together after the depth is set. A 3 mm
7
( / in.) hex screwdriver or bit is required to
64
tighten these screws.
Preparing the Mounting Surface
To obtain a clean, flat look when the device is mounted, you
must precisely cut and prepare the mounting surface.
1
Trim the template and make sure it fits in the location where
you want to mount the device.
2
Remove the protective liner from the back of the template
and adhere it to the location where you want to mount the
device.
3
Using the drill bit indicated on the template, drill one or more
of the holes inside the corners of the solid line on the
template to prepare the mounting surface for cutting.
4
Using an appropriate cutting tool, cut the mounting surface
along the inside of the solid line indicated on the template.
Make sure that you leave the full width of the solid line on the
template intact when cutting, so you can enlarge and refine
the cutout as necessary.
5
Remove the template from the mounting surface.
6
Select an option:
• If the mounting surface is thicker than
use a router or other appropriate tool to reduce the
thickness of the rear surface around the cutout.
• If the mounting surface is thinner than
add a surface reinforcement around the device cutout.
7
Place the device into the cutout to test the fit, and refine both
the cutout and the rear surface as needed.
Installing the Flat Mount Bracket and Mounting the
Device
Before installing the brackets and mounting the device, you
must prepare the surface so it is the appropriate thickness for
the device and sturdy enough to support the device.
The screws provided to connect the brackets to the mounting
surface may not be appropriate for all surface types or
thicknesses. If the screws are too long for your surface, or
inappropriate for the surface type, you must purchase
appropriate screws.
1
Place the device in the cutout
will fit better on either the top and bottom or the sides of the
device.
1
/ in. (3.2 mm),
8
1
/ in. (3.2 mm),
8
to determine if the brackets
2 Install the threaded rods
back of the device.
3
Place the device bracket
the bracket to the device with the included lock nuts.
4
Connect the surface brackets
the hex screws , but do not tighten them.
The brackets must remain loosely connected so that you can
adjust the depth after the surface brackets are installed in the
mounting surface.
5
Place the device in the cutout and mark the location of the
pilot holes needed to secure the brackets to the surface.
6 Remove the device from the cutout, and drill the pilot holes
using a drill bit appropriate for the surface and screw size.
NOTE: Make sure you do not drill through the front of the
surface.
7
Install the rubber gasket around the front bezel of the device.
8
Apply marine sealant to the front bezel of the device so that it
will fill and properly seal the area between the mounting
surface and the device and prevent leakage behind the
dashboard.
9
Place the device in the cutout, and secure the brackets to the
surface using the appropriate screws and washers.
10
Adjust the depth of the device until it is flat with the front of
the surface, and use the hex screwdriver to tighten the hex
screws that secure the two brackets.
11
After the device is adjusted correctly, remove any excess
marine sealant.
Instructions d'installation du kit
d'intégration pour les GMI™ 20 et
GHC™ 20
Le matériel fourni dans ce kit vous permet d'installer votre
appareil de façon à ce que l'écran affleure à la surface de la
console (montage intégré). Pour ce type d'installation, l'arrière
de la surface de montage doit être totalement accessible et
vous devez savoir découper ou créer de façon précise une
surface de montage afin de compléter l'installation de façon
appropriée. Il est fortement recommandé d'avoir recours à un
technicien ou à une société spécialisé dans la modification de
tableau de bord.
in the four mounting holes on the
on the threaded rods, and secure
to the device bracket using
3