Publicidad
Idiomas disponibles
Idiomas disponibles
English
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger from
the AC outlet before cleaning. Dirt and grease may be
removed from the exterior of the charger using a cloth
or soft non-metallic brush. Do not use water or any
cleaning solutions.
Wall Mounting
Some D
WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power
source and remove the battery pack before
making any adjustments or removing/installing
attachments or accessories. An accidental start-up
can cause injury.
Installing and Removing the Battery Pack
(Fig. D)
nOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
align the battery pack with the rails inside the battery
port and slide it in until the battery pack is firmly seated
in the adjustable work light
not disengage.
2. To remove the battery pack
light
1
, press the release button
battery pack
13
out of the adjustable work light
Insert it into the charger as described in the charger
section of this manual
8
into the battery port
13
and ensure that it does
1
13
from the adjustable work
14
and firmly pull the
1
Positioning the Articulating Head LEDs
(Fig. A, F)
WARNING: Do not to attempt to operate the
articulating head LEDs in the closed position, or
with the lens facing the adjustable work light, as
the surface the light may get hot.
The articulating head LED
and swivels from 0°–270°.
nOTE: The adjustable work light is equipped with magnetic
sensors. If the articulating head LED
lens facing the adjustable work light, the articulating head
LED
3
,
5
will not turn on and will turn off automatically.
1. To move the left articulating head LED
articulating head LED
from the adjustable work light
2. To adjust the light beam, swivel the left articulating head
LED
5
or right articulating head LED
the desired position.
3. When not in use fold the left articulating head LED
right articulating head LED
into the stored position, secured in the adjustable
work light
1
On/Off Switch (Fig. A, F)
WARNING: The lens gets very hot during use. To
reduce the risk of burns, do not touch hot lens.
WARNING: Keep objects at least 20" (51 cm) away
from the lenses when they are in use to prevent
the objects from overheating.
WARNING: To reduce the risk of fire, keep away
from combustible materials while in operation.
CAUTION: Do not stare into box light lens. Serious
eye injury could result.
nOTE: For best results, make sure your battery pack is fully charged.
1. To turn on the right articulating head LED
right LED On/Off button
2. To turn on the left articulating head LED
LED On/Off button
3. Each articulating head LED
levels, up to 2000 lumens. Continue to press the On/Off
buttons
2
,
4. Continue cycling the On/Off buttons until the lights turn off.
nOTE: The light box is equipped with magnetic sensors.
If the articulating head LED
facing the light box, the articulating head LED
not turn on and will tun off automatically.
,
8
Low Battery Indicator
As the battery nears a fully discharged state, the light will
blink twice. The light will continue to blink twice every 45
seconds until the battery is fully discharged at which time
the light will turn off. Indication time will vary based on
battery pack capacity.
.
CAUTION: Stop work and replace the battery when
this occurs.
,
piviots up and down 0°–160°
3
5
3
,
5
first pull it upwards and away
3
.
1
with the lens side facing
3
.
.
2
4
.
3
,
5
has three brightness
4
to change the brightness level.
3
,
5
is stored with the lens
is stored with the
or right
5
3
by twisting it into
or
5
, press the
3
5
, press the left
3
,
5
will
Publicidad
