Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
5.
Place the robot on the charging base and make sure the charging terminals on the robot
match those of the charging base. Once the robot is properly placed, it will beep once
and the power button will light up. If the light is oscillating orange, it means the battery
is not completely charged. To ensure the maximum cleaning time, wait until the light
turns into steady blue, as this will indicate the battery is fully charged and the robot is
ready to clean. Fig. 18
4. OPERATION
Starting the cleaning. Fig. 19
1.
Hold down the Start/Pause button on the robot to turn it on.
2.
Press the Start/Pause button on the robot vacuum cleaner or on the app to start
cleaning.
Note:
-
If the robot runs out of battery while cleaning, it will automatically return to the charging
base. Once the battery is fully charged, the robot can start a new cleaning cycle.
-
If there is no good access to the charging base, the robot will not be able to return to it. If
this happens, place it manually on the charging base.
Pausing the cleaning.
Fig. 19
1.
Press the Start/Pause button on the robot vacuum cleaner or on the app to pause the
cleaning process.
2.
Press the Start/Pause button on the robot vacuum cleaner or on the app to resume the
cleaning process.
Off. Fig.
19
Hold down the Start/Pause button on the robot to turn it off.
Warning
The robot vacuum cleaner has a power switch (with positions I and 0) located on the lower
part of the main body. If the robot will not be used for long periods of time, it is recommended
to turn it off using this switch. As a safety measure, if the robot is switched off (0 position),
it will restore the factory default settings. To operate the robot, the switch must be in the on
position (I)
Cleaning modes
This robot includes different modes and functions that can be activated via the app.
42
Auto mode. Fig.
19
-
Press the Start/Pause button or select the auto cleaning mode on the app, then the robot
vacuum cleaner will start the automatic cleaning.
-
The robot will clean the whole surface, edges, around objects such as tables, chairs etc.,
until the battery is low, then it will return to the charging base.
Scrubbing mode. Fig. 20
-
Attach the mop to the mixed tank and fill the tank with water.
-
Place the mixed tank on the robot vacuum cleaner and select the scrubbing level with the
remote control: high, medium or low.
-
Once you have selected the desired scrubbing level, the robot vacuum cleaner will start
the All in One function to vacuum, scrub and sweep simultaneously thanks to its mixed
tank.
Note:
-
If you wish to mop, do not fill the water tank.
-
If the robot has the mixed tank installed with water in it, when it leaves the charging base,
it will turn around itself to soak the mop.
-
To ensure a perfect scrubbing from the start, it is suggested to dampen the mop evenly
with water before fixing it to the mixed tank. It is also recommended to wash the mop
after every use.
-
It is recommended to be present when the robot is scrubbing.
-
When the robot vacuum cleaner returns to the charging base, you must remove the mop.
Do not leave the robot vacuum cleaner charging with the mop assembled.
Spiral mode. Fig. 21
-
The robot will carry out an intense cleaning of a specific area when this mode is activated.
The robot will start cleaning in a specific spot and will move outwards performing spiral
movements (1 metre). Then, it will return to the start point by performing inwards spiral
movements again.
-
Once it has finished and returns to the starting spot, the robot will start cleaning in Auto
mode until it runs out of battery.
-
Before using this mode, place it in the spot you wish to clean.
-
Select the spiral cleaning mode on the app.
Edge mode. Fig. 22
-
When this mode is selected, the robot will clean along walls and around furniture (e.g.
table or chair legs).
-
Select the edge cleaning mode on the app.
ENGLISH
43
Publicidad
