cecotec CONGA ROCKSTAR 1600 X-TREME Manual De Instrucciones página 26

ENGLISH
Press the speed selector to select the device operating speed: LOW, MED, HIGH and AUTO.
-
The device will turn on with the LOW mode by default.
If you select the AUTO mode, the device will automatically adjust suction power according
-
to the concentration of dust and the type of surface.
When operating at high speed and a battery at 20% or lower, the device will automatically
-
switch to medium speed in order to lengthen the battery life.
The vacuuming brush head can remove dust from carpets, hard and soft floors, and tiles.
-
If too many particles or fibres are vacuumed, or if a child touches the brush during operation
-
by accident, the rotary brush stops spinning automatically in order to prevent tangles and
possible damage.
Accessories
This device includes different accessories that allow cleaning different types of surfaces,
objects and dirt. Some of them are suitable for the upright vacuum cleaner, and others are
preferably used with the handheld one.
Jaliscazo brush:
Assemble this brush to the upright vacuum cleaner. This brush is especially designed for
cleaning hard floors, but can be used to efficiently clean soft floors too.
2-in-1 narrow accessory for corners and furniture
Fig. 4
This accessory is preferably used with the handheld vacuum cleaner and allows cleaning
furniture without damaging it and reaching less accessible dirt in corners.
Charge and display
When the battery percentage is 20 % or below, the device will automatically enter the
-
low consumption mode. It is recommended to charge the device when it reaches this
percentage.
During charging, the charge light indicator will turn on red and the display will show the
-
current charge percentage. When the device is fully charged, the battery indicator will turn
green and the display will show 100%. Fig. 5
You can charge the battery when the battery is installed or not in the device. Connect the
-
adapter and connect the other end to the battery, paying attention to the direction. Once it
is properly connected, the charge light indicator will turn on red and will turn green once
the charge is complete. Fig. 6-7
50
5. CLEANING AND MAINTENANCE
Turn the appliance off, unplug it from the power socket and allow it to cool down before
-
cleaning it.
Use a soft, slightly dampened cloth to clean the device's surface.
-
Never immerse the device in water or other liquids, do not allow liquids to enter the device.
-
Do not use sponges, powder products or abrasive cleaning agents to clean the product.
-
Do not leave the device in a place with direct sunlight.
-
Do not leave the device in a wet place after cleaning it.
-
After the brush has been used for a long time, bristles might start to tangle with hair and
-
other particles. Clean it in order for it to operate correctly again.
Filters and tank cleaning
To avoid the appliance from overheating and losing suction power, it is suggested to clean
-
the filters frequently. To make the most of the suction power, it is suggested to clean the
filter after every use.
The filters shelf life will depend on the accumulated use and the type of particles which are
-
frequently vacuumed. It is recommended to replace the filters every 6 months.
To remove the filters (Fig. 8):
-
1. Press the dust tank opening button, marked with the word "CLEAN", and pull on the metallic
handle to remove the filtering system.
2. Once the filtering system is out, turn the metallic handle anticlockwise and you will be able
to take the high-efficiency filters out.
Vacuum and shake the filters to remove every particle and dust remain that may block
-
them and difficult the correct air circulation. Remember not to use the vacuum cleaner
without the filters properly assembled.
Filters cannot be washed inside a washing machine nor dried with a hair dryer.
-
Do not brush the high-efficiency filter.
-
To empty the dust tank, press the dust tank lower cover opening button, open it and empty
-
it. Fig. 9
Cleaning the Jaliscazo brush
Fig. 10
1. Move the rotary brush release button with the finger toward the arrow and remove the
cover of one of the ends of the brush.
2. Take one end of the brush out as shown on the image.
It is important to clear and clean all the residues left in the brush rotary axis.
-
If you decide to wash the brush, you must air dry all the pieces. Assemble the pieces back
-
in order to use the brush again.
ENGLISH
CONGA ROCKSTAR 1600 X-TREME 51