Metabo RC 12-18 32W BT DAB+ Manual Original página 14

en ENGLISH
music
DYNAMIC LABEL = Information broadcasted by
the station as scrolling text
FREQUENCY = station frequency
SIGNAL STRENGTH = signal strength (WEAK =
weak, STRONG = strong)
Select the desired setting by turning the (3)
button and confirm by briefly pressing the (3)
button.
Time mode (12 h / 24 h)
Press the "MENU" button (2), by turning the (3)
button go to sub-item "SET CLOCK". Briefly
pressing the (3) button takes you to the selection
menu.
"24 H MODE"
"12 H MODE" = (AM / PM)
Select the desired setting by turning the (3)
button and confirm by briefly pressing the (3)
button.
Set the time (hours) by turning the (3) button and
confirm by briefly pressing (3) button. Set the
time (minutes) by turning the (3) button and
confirm by briefly pressing the (3) button.
Display backlight:
Press the "MENU" button (2), go to the sub-item
"BACKLIGHT" by turning the (3) button. Briefly
pressing the (3) button takes you to the selection
menu.
AUTO = lighting switches off automatically after
10 sec
ON ALL TIME= lighting always on
Select the desired setting by turning the (3)
button and confirm by briefly pressing the (3)
button.
Speaker light:
Press "MENU" button (2), go to the sub-item
"SPEAKER LIGHT" by turning the (3) button.
Briefly pressing the (3) button takes you to the
selection menu.
AUTO = lighting on for 10 sec.
ON = lighting on
OFF = lighting off
Select the desired setting by turning the (3)
button and confirm by briefly pressing the (3)
button.
Reset to factory settings
Press "MENU" button (2), go to the sub-item
"RESET ALL" by turning the (3) button. Briefly
pressing the (3) button takes you to the selection
menu.
NO = cancel process
YES = reset to factory settings
Select the desired setting by turning the (3)
button and confirm by briefly pressing the (3)
button.
8. Charging function
Charging is only possible when the unit is switched
on or in standby mode.
14
8.1 Charging battery pack
The battery symbol in the display
(12) shows the charge level of the
battery pack (25) used.
If the mains cable is connected and a
battery pack that is not fully charged
is inserted, it will be charged (the
battery symbol flashes).
Remove battery pack:
Press the battery pack release (24) button and
remove the battery pack (25).
Insert battery pack:
Push the battery pack (25) completely to the stop
on the sliding seat.
8.2 Wireless charging of a smart phone
(inductive charging)
Only intended for smart phones that have this
charging technology. Place the smart phone on the
marked area (18), it will be charged.
8.3 Charging a USB device
Only connect USB devices which are
compatible with the USB standard. Using
incompatible devices can lead to malfunctions,
damage or injuries.
Open the cover (13) and plug a USB device with a
suitable cable into the USB-C port (15). The device
is charged.
9. Troubleshooting
Is the Bluetooth connection bad or
interrupted?
-> reduce the distance between the devices
No charging function?
-> The radio must be switched on or be in standby
mode.
-> Plug in the mains plug
-> Check if an error message appears in the display
(12). Error messages and their meaning, please
refer to the following text. Remove the battery pack,
eliminate the error, insert the battery pack again.
"Batt Err" = temperature of the battery pack too high/
too low. Permissible charging temperature range: 0
°C to 60 °C.
"Batt Err" = battery pack not inserted correctly.
"Batt Err" = battery pack defective. Remove the
battery pack immediately from the charger.
"Critical Error" = battery pack not recognised.
Wrong brand?
Display is discolored black?
-> Increased temperature due to sunlight can lead
to discoloration. This disappears again at normal
temperature. Observe the permitted ambient
temperature.
10. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.