Publicidad
Charger for Apple Watch
EN
Chargeur pour Apple Watch
FR
• Do not short-circuit connectors and circuits.
Do not operate a device if it is not in working order. In such
cases, it must be secured against unintentional further use.
• Use product, product parts and accessories only in per-
fect condition.
• In case of questions, defects, mechanical damage, troub-
le and other problems, non-recoverable by the documen-
tation, contact your dealer or producer.
• Avoid stresses such as heat and cold, moisture and di-
rect sunlight, microwaves, vibrations and mechanical
pressure.
Not meant for children. The product is not a toy!
• Secure packaging, small parts and insulation against ac-
cidental use.
Heat storage
Heat is generated during inductive charging.
• Make sure that there are no metal parts on the back of
your device.
Metal heats up strongly in the induction field and can cause
damage to the product or your end device.
• Do not cover the product.
Magnetism
The product contains magnetic materials.
• Consult a medical professional before you use the pro-
duct to make sure it is compatible with implanted medi-
cal devices.
• Maintain a minimum distance of 20 cm from medical de-
vices.
• Do not operate and/or store the product near credit, debit
or other bank cards.
Tripping Hazard
• Install the system and devices attached to it in a way that
persons cannot be injured, or objects not be damaged for
example by dropping or stumbling.
2 Description and function
2.1 Product
The product is an inductive charger for charging all models
of the Apple Watch from series 2 onwards. The charger has
a magnetic surface for a firm hold of the Smartwatch and is
connected to a power source via a USB-C™ plug. An adap-
ter plug for connection to a USB-A socket is also included in
the scope of delivery.
2.2 Scope of delivery
Charger for Apple Watch, Adapter plug, User Manual
2.3 Operating Elements
See Fig. 1.
1 Charging interface
2 USB-C™ plug
3 Adapter plug with USB-A plug and USB-C™ socket
3 Intended use
This product is intended exclusively for private use
and its intended purpose. This product is not inten-
ded for commercial use. We do not permit using the
device in other ways like described in chapter „Description
and Function" or in the „Safety Instructions". Use the product
only in dry interior rooms. Not attending to these regulations
and safety instructions might cause fatal accidents, injuries,
and damages to persons and property.
IPX0: This product is not protected against water.
4 Preparation
1. Check the scope of delivery for completeness and in-
tegrity.
2. Compare the specifications of all used devices and ensu-
re compatibility.
5 Connection and operation
1. Connect the charger to a suitable power source via the
USB-C™ plug (2).
This can be either a mains adapter, a car charger adapter or
a USB socket on the PC.
If no USB-C™ port is available, use the adapter plug (3) to
connect to a USB-A socket.
2. Place your Smartwatch on the charging interface (1).
The charging process stops automatically as soon as the
REV2023-11-15
Subject to change without notice. |
V1.0anw
Sous réserve de modifications.
Smartwatch is fully charged.
3. Remove your Smartwatch from the charger after char-
ging.
6 Maintenance, Care, Storage and
Transportation
The product is maintenance-free.
NOTICE!
• Only use a dry and soft cloth for cleaning.
• Do not use detergents or chemicals.
• Store the product out the reach of children and in a dry
and dust-protected ambience when not in use.
• Store cool and dry.
• Keep and use the original packaging for transport.
7 Disposal instructions
According to the European WEEE directive, electrical
and electronic equipment must not be disposed with
consumers waste. Its components must be recycled
or disposed apart from each other. Otherwise conta-
minative and hazardous substances can damage the
health and pollute the environment.
As a consumer, you are committed by law to dispose electri-
cal and electronic devices to the producer, the dealer, or pub-
lic collecting points at the end of the devices lifetime for free.
Particulars are regulated in national right. The symbol on the
product, in the user manual, or at the packaging alludes to
these terms. With this kind of waste separation, application,
and waste disposal of used devices you achieve an important
share to environmental protection.
WEEE No: 82898622
8 EU Declaration of conformity
Hereby Goobay®, a registered trademark of
Wentronic GmbH, ensures that the mentioned
radio system type is conformed to Directive
2014/53/EU. The full text of EU Declaration of Conformity is
available at the following Internet address:
https://www.wentronic.com/en/
Enter the item number in the search bar to go to the specific
item page. The current declaration of conformity is available
in the download section.
1 Consignes de sécurité
Le mode d'emploi fait partie intégrante du produit et com-
prend d'importantes informations pour une bonne installation
et une bonne utilisation.
• Lisez le mode d'emploi attentivement et complètement
avant de l'utiliser.
Le mode d'emploi doit être disponible à des incertitudes et
transfert du produit.
• Conservez soigneusement ce mode d'emploi.
• Ne pas ouvrir le boîtier.
• Ne modifiez pas le produit et les accessoires.
• Pas court-circuiter des connexions et circuits.
Un appareil défectueux ne doit pas être mis en service. Il doit
au contraire être protégé contre toute utilisation involontaire.
• Utilisez le produit, pièces et accessoires des produits uni-
quement en parfait état.
• En cas de questions, les défauts, les dommages mécani-
ques, des ingérences et d'autres problèmes, non récupé-
rables par la documentation, contactez votre revendeur
ou le producteur.
• Éviter des conditions extrêmes, telles que la chaleur ex-
trême et froid, l'humidité et de la lumière directe du so-
leil, ainsi que microondes, des vibrations et de la pressi-
on mécanique.
Non destiné à des enfants. Le produit n'est pas un jouet !
• Sécuriser l'emballage, petites pièces et l'isolation contre
l'utilisation accidentelle.
Accumulateur de chaleur
De la chaleur est générée pendant la charge par induction.
• Assurez-vous qu'il n'y a pas de pièces métalliques à l'ar-
rière de votre appareil.
Le métal se réchauffe fortement dans le champ d'induction et
peut endommager le produit ou votre appareil final.
• Ne couvrez pas le produit.
Goobay® by Wentronic GmbH | Pillmannstraße 12
- 3 -
38112 Braunschweig | Germany | cs@wentronic.com
65343
Material damage
Publicidad
