Publicidad
Idiomas disponibles
Idiomas disponibles
Control panel
GB
(Fig.1 on page 3)
A. Output: 12V (
) 2A
B. Input: 12V (
) 2A
C. Type-C output: 2 x 5V (
D. "Delete" button
E. "UP/DOWN" button
F. "Call" button
G. "Function" button
H. "ON/OFF" button
I. Charging input: 5V (
J. "Cancel" button
K. Charging indicator
i. Flashing: Charging
ii. Always on: Full charged
L. Type-C Input: 5V (
M. Input: 12V (
) 2A
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
Operating instructions
• This radio uses electromagnetic energy in the radio frequen-
cy (RF) spectrum to provide communications between two or
more users over a distance. RF energy, which when used im-
properly, can cause biological damage.
• Each one keyboard transmitter could expand 998 coaster
pagers.
• During programing and setting, pagers must be being
charged.
1. Connect the adaptor to the main power supply.
2. Transmitter is powered by the output of adaptor.
3. Either the charger could be powered via Type-C cable by
the output of transmitter (5V (
tor(12V (
) 2A) directly.
4. The product is in default operation mode and ready to use.
You can input the corresponding numbers shown on pagers
and press "Call" button to call the pagers.
5. Press "ON/OFF" button, "C999" is displayed. Press "Call"
button, all charging pagers will be turned off. The pagers
will be turned on again during charging. NOTE: The "ON/
OFF" setting will not affect the pagers which are not charg-
ing.
6. Under operation mode, press UP/DOWN button to query 10
call histories. You can press "Call" button directly to call the
corresponding pagers in shortcut.
8
) 2A
) 4A
) 2A
) 2A) or by output of adap-
Function:
A. F1 – Programming
All pagers are programmed before delivery. So this opera-
tion is only necessary when adding new pagers or changing
numbers.
Press FUNCTION, F1 is displayed. Then press CALL to enter
programming status.
In programming status, P--- is displayed. Charging indica-
tor on charging pagers will be off, and other LED will be on.
Input the number, and all charging pagers display the num-
ber. Then pick up a pager, and it beeps to indicate the num-
ber has been accepted.
Repeat above steps to program other pagers.
Note: The pagers will quit programming mode if no opera-
tion within 1 minute. All pagers' numbers will not change if
not being programmed. 1 pager only can be programmed 1
number. Old number will be replaced by the new one.
B. F2 – Set alarm mode
Press FUNCTION, and find F2 by pressing UP/DOWN but-
ton. Then press CALL to enter.
Please refer to settings table at the end of the manual for
setting alarm mode.
A*** is displayed in F2.
C. F3 – Set alarm time
Press FUNCTION, and find F3 by pressing UP/DOWN but-
ton. Then press CALL to enter.
Please refer to settings table at the end of the manual for
setting length of alarm time.
L*** is displayed in F3.
D. F4 – Set alarm repeat time
Press FUNCTION, and find F4 by pressing UP/DOWN but-
ton. Then press CALL to enter.
Please refer to settings table at the end of the manual for
setting repeat alarm time.
Γ*** is displayed in F4.
E. F5 – Edit transmitter ID
Press FUNCTION, and find F5 by pressing UP/DOWN but-
ton. Then press CALL to enter.
Please refer to settings table at the end of the manual for
editing transmitter ID.
E*** is displayed in F5.
F. Call history
Press UP/DOWN button to query call history.
The number in call history can be called directly by pressing
CALL.
Maximum 10 recent called records can be queried.
Note: No looping of UP/DOWN button.
G. In CALL mode
Short press POWER button and C999 is displayed. Then
press CALL, and all charging pagers will be off. Re-charge
pagers will turn on again.
Note: This instruction is invalid to the pagers not being charged.
Publicidad
