Reflex Reflexomat RSC Smart Manual De Instrucciones Original página 22

Technical data

Note!
Additional equipment for topping up water,  4.6 "Optional equipment
and accessories",  22.
4.5 Scope of delivery
The scope of delivery is described in the shipping document and the content is
shown on the packaging.
Immediately after receipt of the goods, please check the shipment for
completeness and damage. Please notify us immediately of any transport damage.
Basic pressure-maintaining equipment:
•
A Reflexomat primary vessel (optionally 200l/300l/400l/500l or 600l) and a
compact design control unit.
•
"LIS" weight measuring cell for filling level measurement.
•
Cap valve
• Hose for "EC" system connection
•
Mains cable with plug (230V~)
4.6 Optional equipment and accessories
•
For make-up with water
–
Solenoid valve "Fillvalve" with ball valve and Reflex Fillset for make-up
with potable water.
•
Fillset Impulse with FQIRA+ contact water meter for make-up with potable
water.
•
Fillsoft for softening or demineralisation of the make-up water from the
potable water system.
–
Fillsoft is installed between Fillset and the device. The device controller
evaluates the make-up quantities and signals the required replacement
of the softening cartridges.
•
Fillguard for conductivity monitoring
–
If the Fillguard is fitted, the capacity of Fillsoft Zero demineralisation
cartridge can be monitored based on the conductivity.
•
Optional expansions for Reflex controllers:
–
RS-485 interface with Modbus RTU (integrated).
–
Servitec S
•
Membrane rupture detector

Note!
Separate operating instructions are supplied with accessories.
5 Technical data
5.1 Control unit
Permissible flow temperature
Permissible operating temperature
Permissible ambient temperature
Permissible membrane temperature
Control unit protection (IP) rating
Compressor protection (IP) rating
Noise level
Operating voltage
Nominal capacity
Rated electrical current
Pre-fuse, max.
Number of RS-485 interfaces
Weight
22 — English
90 °C
5 – 70 °C
5 – 40 °C
-10 – 70 °C
IP 54
59 dB(A) / 1 bar
230 V / 50 Hz / 1 ph
0.37 kW
2.6 A
16 A
1
With 200 l vessel 52 kg
With 300 l vessel 60 kg
With 400 l vessel 74 kg
With 500 l vessel 84 kg
With 600 l vessel 96 kg
Reflexomat RSC Smart — 08.01.2024-Rev. A
5.2 Vessel
Vessel without controller (volume 200 l)
6 Installation
DANGER
Risk of serious injury or death due to electric shock.
If live parts are touched, there is risk of life-threatening injuries.
•
Ensure that all phases of the mains power supply to the product are
disconnected prior to installation. (Pull out the power plug.)
•
Ensure that the system is secured and cannot be reactivated by other
persons.
•
Ensure that installation work for the electric connection of the device is
carried out by an electrician, and in compliance with electrical
engineering regulations.
CAUTION
Risk of injury due to pressurised liquid
If installation, removal or maintenance work is not carried out correctly, there is
a risk of burns and other injuries at the connection points, if pressurised hot
water or hot steam suddenly escapes.
•
Ensure proper installation, removal or maintenance work.
•
Ensure that the system is de-pressurised before performing installation,
removal or maintenance work at the connection points.
CAUTION
Risk of burns on hot surfaces
Hot surfaces in heating systems can cause burns to the skin.
•
Wear protective gloves.
•
Please place appropriate warning signs in the vicinity of the device.
CAUTION
Risk of injury due to falls or bumps
Bruising from falls or bumps on system components during installation.
•
Wear personal protective equipment (helmet, protective clothing, gloves,
safety boots).