Publicidad
SPECIFICATIONS
AC MODE
Input / Output Voltage 56 V
Compatible Hub
PGX1600E-H
Approximately
Charging Time
170 min for HC2240T
(40.0 Ah)+2 x BA4200T (7.5 Ah)
Recommended
5 – 40 °C
Charging Temperature
Recommended
-20 – 70 °C
Storage Temperature
Weight
17.6 kg
DC MODE:
Output Voltage
56 V
Output Power
2 x 700 W
45 min for 2 x BA4200T
Charging Time
(7.5 Ah)
Recommended
5 – 40 °C
Charging Temperature
Recommended
-20 – 70 °C
Storage Temperature
RECOMMENDED ACCESSORIES
WARNING:
Use only identical replacement
parts listed below. Use of parts that do not meet the
original equipment specifications may lead to improper
performance and compromised safety.
PART NAME
PGX
70 cm Charging Cable
TM
PGX
150 cm Charging Cable
TM
DESCRIPTION
KNOW YOUR POWER BANK (Fig. A)
1.
High-capacity Battery Bay
2.
High-capacity Battery-release Lever
3.
Portable Battery-release Button
4.
Charging Cable
5.
Portable Battery Bay (x 2)
6.
Mounting Hole
7.
Port (x 2)
8.
Anti-theft Bar
9.
10. Power Button (Bluetooth
11. Bluetooth
12. High-capacity Battery-bay Status Indicator
13. DC Status Indicator
14. AC Status Indicator
15. Bracket (2)
16. M8 x 25 Bolt and Washer Set (4)
17. M8 x 50 Bolt and Washer Set (4)
18. M8 x 95 Bolt and Washer Set (2)
19. 5 mm Hex Wrench
OPERATION
In AC Mode, the EGO PGX
only work with EGO PGX
charge EGO high-capacity and portable battery packs.
In DC Mode, EGO high-capacity battery (HC2240T) can
charge portable EGO battery packs via the EGO PGX
power bank.
CHARGING BATTERY PACKS - AC Mode
NOTE:
charged. Before using them for the first time, fully charge
the battery packs.
with attached battery packs must be placed in a
well-ventilated area.
The following illustrations in Fig. C1 show how to
charge the battery packs via the power bank(s):
1.
NOTE: To disconnect the hub from the power bank, as
shown in Fig. C2.
MODEL NUMBER
2.
ACE0700
ACE1500
3.
4.
56 VOLT PGX
Portable Battery-bay Status Indicator
Button)
®
Indicator
®
power bank is designed to
TM
1600W hub PGX1600E-H to
TM
Lithium-Ion battery packs are shipped partially
WARNING:
During charging, the power bank
Push the collar of the hub connector to the port on
either side of the power bank until you hear a click
as shown in Fig. C1 (step 1).
Connect the power bank to the next power bank in
the same way using provided cable (ACE0700) or
ACE1500 (sold separately) to the 2nd port on the
opposite side of the power bank. You can continue
to connect more power banks (no more than 30 to a
single hub) if necessary (step 2).
Plug the hub into the power supply (step 3). The hub
status indicator and power bank AC status indicator
will glow green, indicating that the hub and the
power bank are working properly and can charge the
battery packs.
Align the raised ribs of a battery pack with the
mounting slots in one of the power bank's battery
bays. Slide the battery pack down into the battery
bay (step 4). The battery release button will spring up
indicating that the battery pack is securely attached.
POWER BANK — PGX1400PB
TM
EN
TM
7
Publicidad
