METRO PROFESSIONAL GSM1010 Instrucciones página 2

Dear Customer,
Congratulations on your purchase of this product.
Please take a few minutes before starting operation of the appliance and
read the following operating
instructions.
Many thanks.
EN
MODELS
This manual describes the installation, operation and maintenance of
liquidisers .
The model reference and its characteristics appear on the name plate
attached to the machine.
INTENDED SAFETY CONDITIONS
In order to reduce the possibility of accidents
(short circuits, injuries or fires, etc.), to get the best
performances from the machine and to maintain
it correctly, read and follow these instructions
attentively. Keep the instructions and make sure that
all users of the machine read them before using it.
- This appliance has sharpened blades. Never touch
the blades when they are moving. Handling of
blades should be limited to cleaning and always
with the machine unplugged.
- Before using the machine for the first time, and
always with the machine unplugged, clean the area
in contact with food with (lukewarm) soapy water,
rinse and leave to dry.
- Multiple cleaning cycles before first use.
- Before plugging the appliance in, make sure that the
mains voltage coincides with the voltage indicated
on the name plate attached to the machine. Do not
plug the appliance in if the arm is not inside the
container that you are working with.
- Never operate the machine empty, outside of a
container. The arm should be submerged up to
a maximum of 2/3 of its length. The maximum
working tilt should be 30° (see figure 6).
- To avoid splashes, always work with a stable
container and submerge the arm into the container
before starting and do not remove it until it has fully
stopped moving.
- The bowl must always be firmly resting on the flat
and stable surface.
- Under no circumstances should the appliance be
operated on a surface with an inclination of over 10
degrees with respect to the horizontal plane.
- Never place your hand or any other utensil into the
container where the appliance is working in order to
avoid personal or material damage.
- Always disconnect the machine before removing
the blender arm and also before undertaking any
cleaning, inspection or repair work on the appliance.
- Clean the blender arm after each use as described
below. During each operation, check the status of
the lower seal. If you see any signs of deterioration,
contact the authorised repair service.
- Avoid water entering the motor block and under no
circumstances submerge it in water. If this occurs,
follow these exact instructions:
• Leave the liquidiser inside the container and do
not touch the container.
• Unplug from the mains.
• Remove the appliance from the container and
try to remove as much liquid as possible from
inside it.
• Do not connect the machine again and contact
your seller.
- Do not use the machine when the cable or plug are
damaged. For repair, contact a qualified technician
service.
- Do not use abrasive detergents (bleach, nitric
acid...) or stainless steel scourers or scrubbers
when cleaning the machine. They may cause rust
or the deterioration of materials.
- Do not allow the appliance to be used as a toy.
This machine is not designed for use by people
(including children of 8 years old and up) with
reduced physical, sensory or mental capabilities
or those lacking the necessary experience or
knowledge, unless they have received supervision
or instructions regarding the use of the appliance
from someone responsible for their safety and
understand the risks that this implies. Do not allow
children to play with the appliance. The cleaning
and maintenance to be performed by the user must
not be performed by unsupervised children
- Do not allow comfort or familiarity with the product
(due to using it repeatedly) to substitute strict
compliance with the safety regulations. Stay alert,
pay attention to what you are doing and use
common sense when operating the appliance.
- Do not use the equipment when you are tired or
under the influence of drugs, alcohol or any other
medication. If you use the tool in an unsafe or
incorrect way, you may suffer personal injury or
material damage.
- The models cited in the manual have been designed
for use in hotels, restaurants, hospitals, bakeries,
catering and commercial applications, but never for
continuous industrial manufacturing.
- The manufacturer is not responsible when the
product is used incorrectly or differently than the
use mentioned above. Such as, sanitary use,
chemical use, use in explosive atmospheres...
- Do not use with accessories which are not explicity
- 2 -