Cardin ZVL565.01 Manual De Instrucciones página 18

• The use and installation of these appliances must rigorously respect the indications supplied by the manufacturer. The manufacturer
accepts no liability for damage caused by, or situations arising from, the improper use of these appliances.
Attention! Only for EU customers - WEEE marking.
This symbol indicates that once the products life-span has expired it must be disposed of separately from other rubbish. The
user is therefore obliged to either take the product to a suitable differential collection site for electronic and electrical goods
or to send it back to the manufacturer if the intention is to replace it with a new equivalent version of the same product.
Suitable differential collection, environmental friendly treatment and disposal contributes to avoiding negative effects on the ambient
and consequently health as well as favouring the recycling of materials. Illicitly disposing of this product by the owner is punishable
by law and will be dealt with according to the laws and standards of the individual member nation.
USE
This radio control device allows the remote activation of electrical and electronic appliances with its best use in the
following areas: automatic opening systems, alarm systems and multiple access systems (apartment blocks etc.)
The receiver has been designed for multiple access with up to 3000 users each of which may be memorised or
cancelled individually. The code is memorised in the receiver via radio. Each code is stored in a memory location
which can activate up to 4 functions. 1 transmitter = 4 functions max. = 1 location; 3000 users = 12000 functions max.
Receivers 433 MHz
RCQ433-3G
RCQ433-3G10
RCQ433-WF
Memory module
The codes are stored for an unlimited period in non-volatile memory, which allows retaining the codes even in
the absence of power The receiver comes standard with the MCC24LC256 module for memorising up to 3000
codes, which can be increased to 5000 using the optional MCC24LC512 module. It can also manage the 24LC64
(1000 codes) memory modules. During operation, only one of these modules must be present on the circuit.
Attention! Removing and inserting the memory module must be carried out when the receivers are switched off.
Receiver antenna: The installation of the antenna is fundamental, connected to the receiver it represents the
reception point for the radio control. A tuned antenna ANS400 (433 MHz) / ANQ800-1 (868 MHz) using a coaxial
cable RG58 (impedance 50Ω) with a maximum length of 15 m must be installed between binding posts 19-20. The
antenna should be positioned out of doors in the highest possible point, visible and away from metal structures.
3G/WF Antenna: The antenna for the 3G/WF card, which is a specific card supplied along with the product, must
always be installed. It should be screwed to the dedicated connector on the upper part of the box (see fig. 2).
Antenna extension: In areas with a weak 3G/WF signal it is possible to install the antenna in a different location
using an accessory. The accessory consists of a cable in two different lengths and a holding bracket for installing
the antenna to the wall. The accessory is available in the following formats:
- antenna extension with a 5-metre cable ANSKITGSMWF5 / 5-metre cable ANSKITGSMWF10
The transmitter is pre-coded and is fitted with an integrated circuit which is programmed in the factory with a
unique identification number. All the code parameters are contained in this integrated circuit (external memory
modules are not required) thus making code management more reliable and the system more secure. The
transmitter has an automatic shut down mechanism which cuts in after at least 20 seconds of continuous use
(this limits battery consumption).
Key block function
• A key block function has been added to protect the appliance from accidental activation;
- to activate the function press and hold down "MR" for 8 seconds until the
red led starts flashing, at this point to activate a command you will need to
press the required key three times consecutively;
- to reset the function to standard operation standard press and hold down
"MR" for 8 seconds until the red led starts flashing.
IMPORTANT REMARKS
Receivers 868 MHz
RCQ868-3G
RCQ868-3G10
RCQ868-WF
Description
4-channel 3G receiver with LCD display (3000 codes)
4-channel 3G receiver with LCD display (3000 codes) + SIM
4-channel WF receiver with LCD display (3000 codes)
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
18
1
2
MR