Publicidad
Idiomas disponibles
Idiomas disponibles
Fiche technique
AC S267
5 START-UP AND USED
5a start-up
1 – Fit your nozzle in the nozzle-holder rep.1 at the end of the lance
2 – Connect your compressor pipe to Rep. 2 ( minimum 10 mm inside diameter air hose )
3 – Open the air of your compressor.
4 – Screw on support-bracket 3. Then display the required working pressure on the manometer. The vessel is under
pressure.
5 – Take the blast hose in hands and press the remote control handle rep. 4. This handle, located near the nozzle holder, is
based on a air leak out principle that is why, releasing the handle, there is a permanent air leak out at this handle. The
abrasive is blasted.
6 – To stop the sand-blaster, release the remote control handle.
5b used
Humidity of compressed air can be found in the form of condensation by a physical phenomenon caused by the compression
and the expansion of the air. A decanting glass or a filter is placed on the entry of the machine in order to collect this humidity
and is equipped with a drain cock in the lower part.
-please use these drain cocks in order to permanently leave a slight leak.
-Please ensure that the temperature of the compressed air is not too high by using an air compressor which is correctly
sized ( i.e with an effective output which is higher than the air consumption of machine )
-Please also make sure that the air compressor is correctly ventilated and situated in an airy place.
-Always leave a leak at the drain cocks on your air compressor if it's got some.
Some optional materials have been developed in order to fight even more effectively against humidity. For
sandblasting, ACF manufactures and markets some moisture separators which are sturdy and efficient ( P 104 for
consumption under 2500 litres, P 100 for consumption under 6000 litres and P116/117/118 for a consumption under 12000
litres )
ACF also suggest a cooler with a pneumatic engine which is compact and sturdy in a sash. Please do not hesitate to contact us !!!
6° SERVICING
ACF recommends thorough servicing of all the pneumatic mechanisms in your machine every 500 hours (pneumatic assembly, sand-blasting valve, etc.) ACF can service the
machine on your behalf in its workshops. Please contact our sales department.
-regularly bleed the decanting filter
-regularly clean the inside of the sand-blasting machine.
-if necessary, regularly change the air filter cartridges (if this option is on the machine)
-change clogged bronze filters (ref. 5203079)
-check the hatch seal and the cone seal. Change them if necessary.
7 POSSIBLE CASES OF FAILURE
MALFUNCTIONS
The machine does not
start
The machine does not
stop
Air flow in but does not
flow out or flows out
in spurts
Insufficient air or abrasive
material flow rate
1 INTRODUZIONE
a. Importanza del manuale
Il presente MANUALE DI ISTRUZIONI contiene le informazioni necessarie per l'INSTALLAZIONE, l'UTILIZZO e la MANUTENZIONE della macchina. Si consiglia di attenersi
scrupolosamente alle istruzioni fornite poiché il funzionamento e la durata del dispositivo dipendono esclusivamente da un utilizzo corretto e dal rispetto delle procedure di
manutenzione riportate nel manuale. Si ricorda che in caso di problemi, il nostro SERVIZIO POST-VENDITA è a completa disposizione per fornire qualsiasi informazione
necessaria o provvedere all'eventuale riparazione del prodotto.
Il produttore non si assume pertanto alcuna responsabilità in caso di utilizzo improprio e di inadeguata manutenzione della macchina.
Il MANUALE DI ISTRUZIONI è parte integrante della macchina e dovrà quindi essere conservato per tutta la sua vita utile. L'utente dovrà integrare il manuale con tutti gli
aggiornamenti inviati dal produttore e trasmettere l'intera documentazione a eventuali altri utilizzatori o successivi proprietari.
Utilizzare il manuale facendo attenzione a non danneggiarlo. Non rimuovere, strappare o modificare alcuna delle sue parti, per nessuna ragione.
ACF 21/12/22 modèle O
PROTOUMAT - 35 route de Colmar, 67600 Sélestat
SIRET : 444 448 898 00015
description
1
join of air inlet
water separator filter
2
tank air/abrasive
3
pipe of purge water
4
regulator pressure
5
safety valve
6
PROBABLE CAUSE
1.Compressor not connected or not working
2.Remote control hose punctured
3.Faulty pneumatic component
1.faulty operating handle
2.faulty pneumatic component
1.Dirt in the tank
2.Blockage due to humidity in the valve
3.Abrasive material clogging up the tank
4.Incorrectly graded abrasive material
5.Nozzle blocked
1.Sand-blasting valve too open
2.Compressor flow rate too low
3.Worn nozzle
4.Sanding hose blocked
Contact After-Sales in case of recurrent problems or any other special case
AIR CONSUMPT ION
Ø of the
nozzle
Air consumptionat 6 bars
2 mm
250 L/mn
3 mm
500 L/mm
4 mm
850 L/mm
5 mm
1300 L/mm
6 mm
2200 L/mm
8 mm
3700 L/mm
9,5 mm
5500 L/mm
11 mm
7200 L/mm
12 mm
9500 L/mm
REMEDIES
1-connect the compressor's air supply and start up the compressor.
2-repair or change the hose(s)
3-contact your dealer or our After-Sales Service department
1-check that it is working (stop air at the handle outlet)
2-contact our After-Sales Service department
1-open the drain hatch and empty the tank if necessary.
2-clear the valve, open the decanting drain valve (If the problem persists, insert an
air purifier or cooler) between the sand-blasting machine and the compressor
3-empty the tank and air-blast its interior
4-change the abrasive material or adjust the Ø of the nozzle (if the compressor so
permits)
5-unscrew the nozzle and check that there is no dirt in it
1-close the valve completely, drain your hose, repeat the adjustment
2-adjust the diameter of the nozzle to match the compressor flow rate
3-the diameter of the nozzle has increased through wear and no longer matches the
compressor flow rate => change the nozzle
4-check that nothing is blocking the hose. If need be, empty it
Tél. : 03 88 08 65 06
Grain size of the
abrasive material
0,10 maxi
0,20 maxi
0,30 maxi
0,50 maxi
0,80 maxi
1,00 maxi
1,50 maxi
2,20 maxi
2,50 maxi
ITALIANO
contact@protoumat.fr
www.protoumat.fr
Page
7
7
Publicidad
