Publicidad
Idiomas disponibles
Idiomas disponibles
Technical Information,
Heat Output
Nominal Heat Output
Minimum Heat Output
Maximum Continuous Heat Output
Auxiliary Electricity Consumption
In Standby Mode
No room temperature control
INSTALLATION INSTRUCTIONS
This section describes how to install and set up your fire.
BEFORE YOU START:
•
Ensure that all packing items are removed (read any warning labels carefully) and retain all packing for possible
future use.
•
Before connecting the appliance, check that the supply voltage is the same as that stated on the appliance.
•
Ensure that the appliance is installed on a level surface.
•
Make sure the appliance is switched OFF for installation.
CONNECTIONS REQUIRED IN ADVANCE OF INSTALLATION
ELECTRICAL CONNECTION
Please ensure a 230/240V 16A power socket is located within 1m of the product. The electrical connection should be
accessible during product installation so that the connection can be made to the product easily.
BUILDING THE PRODUCT SURROUND/ENCLOSURE
This product can be built into a wall, surround or structure. Please take note of the product dimensions (Fig.1) and build
your wall, surround or structure accordingly. Suitable clearance should be provided to allow the product to be installed
easily.
You are required to leave a minimum of 400mm from the base of the fuel bed to any shelf/enclosure above the product
(Fig. 2). This will allow enough space above the product to allow the flame effect to form fully and not to be obstructed.
When determining a location for the product, ensure that the unit will not be susceptible to drafts, vents, ceiling fans and
other air currents. Similar to a candle, large movements of air will affect the unit's ability to create and maintain the flame
effect. If the desired location is susceptible to significant air movement, i.e. air vents, the different installation options
illustrated in Fig 2 can be used.
VENTILATION
This product needs free ventilation from underneath to operate correctly. There are slots on the underside of the product
to allow this free air through the product. The free ventilation helps keep the electronic components cool and allows the
mist to rise and leave the product. Please see Fig 3 & 4 for examples of the required ventilation. Please take note of the
requirement for a ventilation opening on the shelf where the product sits, to allow a clear path for the air to get to the
product.
CAS500R-RGB-EU Free Ventilation Area: Minimum 210cm
CAS1000R-RGB-EU Free Ventilation Area: Minimum 420cm
ELECTRICAL CONNECTION
Plug the fire into a 16amp 230/240 Volt outlet. Be sure to have access to the plug after installation to allow for
disconnection. Ensure that the supply cable exits at the back of the fire at the right or left hand corner to suit your supply
socket location and is not trapped under the fire such that it might cause it to be damaged.
INSTALLING THE PRODUCT INTO SURROUND/ENCLOSURE
Once your enclosure has been built to the required dimensions and the electrical connection has been installed, follow
the steps below to install your product.
1.
Sit the product on the constructed base, ensuring the cable is accessible and not caught under the product.
2.
Ensure the product is at the correct height to suit the installation and ensure it is adequately level. This can be done
by adjusting the adjustable feet with a flat head screwdriver. (Fig 5) The levelness of the product can be verified by
checking the on-board spirit level which is located on the metal base towards the back of the fire (Fig 6).
3.
Once the product is at the correct height and is level, centre the product within the opening. If using the LED fuel
bed (which is wider than the product), this can be done by fitting the fuel bed to the product. The fuel bed will centre
itself within the opening and its guides will centre the product underneath (Fig 7).
4.
With the product in its final position, remove the fuel bed and using suitable screws (not provided) screw the product
CAS500R-RGB-EU,
Model No:
230V
P
0.24
Nom
P
0.24
min
P
0.24
max
-
-
P
0.21
Nom
CAS1000R-RGB-EU
240V
230V
0.26
0.47
0.26
0.47
0.26
0.47
-
0.22
0.43
2
2
5
240V
0.51
kW
0.51
kW
0.51
kW
-
0.44
W
Publicidad
