Diamond SG30B/A1-R2 Manual De Instrucciones página 14

be assembled by qualified people after the equip-
ment has been positioned on its place. The assem-
bling instructions are contained in the envelope that
is supplied inside the packing.
The equipment has to be positioned on its definitive
place and levelled by qualified people.
The unit is equipped with the plug and electrical cable
mod. Schuco. It can also be a British G Type.
The cable has to be connected at 3 mt. max. to a 0,03A
differential fused isolator. NEVER CONNECT THE CABLE
TO MAIN SUPPLY LINE DIRECTLY.
Verify that the power supply voltage is as indicated on the
machine rate plate (fig. C).
Power supply
230 V
220 V
110 V
To ensure correct operation, the maximum voltage varia-
tion must be between +/- 6% of the nominal value.
We recommend to connect the unit to a dedicated circuit
and not to use damaged sockets, extension sockets or
multiple sockets.
In case of incompatibility between the socket and the plug
of the refrigerated cabinet, the plug should be replaced
with a suitable one by a qualified technician.
For units with electric sockets the maximum rating is 1000
W.
During the electrical connection it is forbidden:
- To use adapter sockets or extension sockets.
- To connect other appliances to the same power
socket.
- To pull the electrical cable or the unit to unplug the
equipment from the socket (fig. A).
- To use extension sockets, worn down cables, cables
with damaged or fissured insulation as they are very
dangerous: they could cause sparks, electric shock
and fire.
- It is absolutely prohibited to pass cables and con-
nect other sockets under the cabinet.
During the electrical connection verify:
- The power supply cable has to be laid in such a way
as to prevent it from being damaged or becoming
hazardous to people and things.
- In case the power supply cable is damaged, it
should be replaced only by a qualified technician
(electrician) with an equivalent cable.
50 Hz single phase
60 Hz
60 Hz
- The cable of the equipment should be checked re-
gularly. If it should result that the cable is damaged
or deteriorated, disconnect the equipment and do
not use it and let the cable be replaced with an ori-
ginal replacement part by an authorised technician.
- Protect the cable in such a way as to prevent twi-
sting or interlacement with other cables, trample on,
crushing, stretching.
A wrong installation could cause damages to peo-
ple, animals or things, for which the manufacturer
cannot be deemed responsible.
12. FIRST CAREFUL CLEANING
DURING THE WHOLE CLEANING OPERATION USE
WORKING GLOVES OF CLASS II TO PROTECT
YOUR HANDS ALL THE TIME AND THE PERSONAL
PROTECTIVE EQUIPMENT ACCORDING TO THE
LAW OF YOUR COUNTRY.
Before switching on the unit, take away the protective film
that covers some external and internal parts of the cabinet
(for example display surface, shelves, front decoration
panels, etc.). Clean the refrigerated cabinet thoroughly,
both inside and outside, using warm water (max. 30°C)
and a solution of bicarbonate of soda (1 tea spoon every
2 liters) or white vinegar. Carefully dry the unit with a soft
cloth.
During the cleaning operation it is forbidden:
- To use detergent products, metal pads or abrasive
substances that could damage the aesthetic appe-
arance of the equipment.
- To use sharp objects (any damage resulting from
the use of these objects will not be covered by war-
ranty).
- To spray water directly on the electric parts and
to wet the electrical parts (fans, lighting, electrical
cables, etc.).
- To wash the refrigerated cabinet with water jets.
Once the cleaning is finished, switch the unit on through
the ON/OFF switch and wait until the cabinet reaches
the proper temperature for the products that have to be
displayed. It will take approx. 3 hours for the cabinet
to reach the proper temperature. The products to be
displayed will have to be already cold according to the
cabinet temperature.
To switch off the display:
- Set the thermostat to 0.
- Switch off using the ON/OFF switch.
- Turn off the light using the ON/OFF switch.
- Unplug the power cord.
- Wait five minutes.
- Clean the display.
15