Publicidad
Idiomas disponibles
Idiomas disponibles
CHARGING PROCEDURE
NOTE: Before using the tool, read the
instruction book carefully.
CHARGING INSTRUCTIONS
1. CHARGING YOUR BATTERY PACK
The charger is designed to charge one or two battery
packs at the same time.
WARNING:
The charger and battery pack are specifically
designed to work together so do not attempt to use
any other devices to charge. Never insert or allow
metallic objects into your charger or battery pack
connections because an electrical failure and hazard
will occur.
2. BEFORE USING YOUR CORDLESS TOOL
Your battery pack is UNCHARGED and you must
charge once before use.
3. HOW TO CHARGE YOUR BATTERY
CHARGING PROCEDURE
1)Plug the charger into an appropriate outlet.
2)Slide the battery pack into the charger. The LIGHT
will become green and flash to show charging has
started.
3)After charging approx 45min/1 hour, the light will
stay green without flashing, which means the battery
is full, and charging is completed.
4
WARNING: When battery charge runs
out after continuous use or exposure
to direct sunlight or heat, allow time for the
battery to cool down before re-charging to
achieve the full charge.
CHARGING INDICATOR
This charger is designed to detect some problems that
can arise with battery packs. Indicator lights indicate
problems (see table below). If this occurs, insert a new
battery pack to determine if the charger is OK. If the
new battery charges correctly, then the original pack
is defective and should be returned to a service center
or recycling service center. If the new battery pack
displays the same problem as the original Battery
Pack, have the charger tested at an authorized service
center.
Light
ON/ flash
Red on
Red flash
- - - - -
Battery charger
Status
Defective Battery
Battery Temperature
Protection
The temperature of
battery pack is less
than 32
F (0
C) or more
o
o
than 113
F(45
C).
o
o
Green on
- - - - - -
Green flash
BATTERY TEMPERATURE PROTECTION
This charger has a battery temperature protection
feature. When the charger detects a battery pack that
is too hot or cold (the light will be red and flash), it
automatically activates the protection circuit, and
suspends charging until the battery pack has reached
the correct temperature. The charging process will
then automatically begin (the light will be green and
flash). This feature ensures maximum battery life.
LEAVING THE BATTERY PACK IN THE
CHARGER
If a fully charged battery pack is left in the charger,
the Light will remain green. The battery pack will
remain charging with a maintenance trickle current.
DEFECTIVE BATTERY PACKS
This charger will detect a defective battery pack.
When a defective battery pack is inserted into the
charger, the charger will try to repair it. This process
will last about 30mins (the light will be green and
flash). If the repair is successful, the charger will
automatically begin to charge the battery pack to the
highest capacity possible (the light will be green and
flash). If the light becomes solid red, the battery pack
is dead.
NOTE: Repaired battery packs are still usable but
should not be expected to perform as much work as
new battery packs.
IMPORTANT CHARGING
NOTES:
1. For a new battery pack or a battery pack that has
been in storage for a long period, please recharge it
before use. If you want to store the battery pack for
a long time, please fully charge the battery pack to
ensure maximum battery life.
2. Longer life and better performance can be obtained if
the battery pack is charged when the air temperature
is between 65 and 75
F (18
0
battery pack in air temperatures below 40
or above 105
F (40.5
C). This is important as it can
0
0
prevent serious damage to the battery pack.
3. Never freeze your charger or immerse charger in
water or any other liquid.
4. When the battery pack fails to produce sufficient
power on jobs that were previously done easily,
Fully Charged
Charging
-24
C). Do not charge the
0
0
F (4.5
C),
0
0
EN
Publicidad
