Publicidad
Idiomas disponibles
Idiomas disponibles
4. Insert and tighten dipstick.
IMPORTANT:
• Check
oil level before
each
use.
Add
oil if needed.
Fill to full line on dipstick.
• Change
the oil after every 25 hours
of
operation
or each
season.
You may
need to change
the oil more
often
un-
der dusty,
dirty conditions.
ADD
GASOLINE
• Fill fuel tank to bottom
of tank filler neck.
Do not overfill.
Use fresh,
clean,
regular
unleaded
gasoline
with a minimum
of 87
octane.
Do not mix oil with gasoline.
Pur-
chase
fuel in quantities
that can be used
within
30 days to assure
fuel freshness.
CAUTION:
Alcohol
blended
fuels (called
gasohol
or using
ethanol
or methanol)
can
attract
moisture
which
leads
to separation
and
formation
of acids
during
storage.
Acidic
gas
can
damage
the
fuel
system
of an engine
while
in storage.
To avoid
engine
problems,
the fue! system
should
be emptied
before
storage
of 30 days
or longer.
Drain
the
gas
tank,
start
the
engine
and
let it run until
the
fuel
lines
and
carburetor
are empty.
Use fresh
fuel
next season.
See Storage
Instructions
for
additional
information.
Never use engine
or
carburetor
cleaner
products
in the fuel tank
or permanent
damage
may occur.
&
CAUTION:
Wipe
off any spilled
oil or
fue!.
Do not store,
spill or use gasoline
near an open flame.
Engine
oil cap
Gasoline
filler cap
Primer
TO STOP
ENGINE
• To stop engine,
move throttle
control
lever to STOP
position.
TO START
ENGINE
1. To start a cold engine,
push primer
three
(3) times
before trying to start.
Use a firm
push.
This
step
is not usually
neces-
sary when
starting
an engine
which
has
already
run for a few minutes.
2.
Move throttle
control
lever to FAST
position.
3.
Hold
upper
handle
firmly
and pull
starter
handle
quickly.
Do not allow
starter
rope to snap
back.
NOTE:
In cooler
weather
it may be
necessary
to repeat
priming
steps.
In
warmer
weather
overpriming
may cause
flooding
and engine
will not start.
If
you do flood
engine,
wait a few minutes
before
attempting
to start and DO NOT
repeat
priming
steps.
Throttle
I!
control-__
!
X
9
Starter
handle
TRIMMING
TIPS
• Set the throttle
control
in the FAST posi-
tion.
If the weeds
or grass
are tall and
thick,
operate
the trimmer
at a slower
walking
speed.
• Frequently
clean
the underside
of the
trimmer
to remove
any grass
build
up.
Keep top of engine
around
starter
clear
and clean
of grass
clippings
and chaff.
This will help engine
air flow and extend
engine
life.
• For best results
and longer
lasting
line, use the ends of the line to do the
cutting.
This is easily
done
by moving
slowly
through
very thick
and heavy
weeds.
• Use the left side of trimmer
when
trim-
ming
along
fences,
walls,
flowerbeds
and other
such objects.
• If trimmer
lines
become
too short,
it
will take longer
to complete
the job.
If
trimmer
lines are worn
to less than
half
their
original
length,
they should
be
replaced.
See "TO REPLACE
TRIMMER
LINE"
in the Maintenance
section
of this
manual.
• Trimmer
head contact
with concrete,
as-
phalt
or other
hard surfaces
may cause
premature
wear
of the ball on bottom
of
trimmer
head.
Publicidad
