Franke FDW 614 E5P E Manual De Usuario página 13

TROUBLESHOOTING
In case your dishwasher doesn't work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.
PROBLEMS POSSIBLE CAUSES
Salt indicator Salt reservoir is empty. (After refill the salt indi-
is lit cator may remain lit for several wash cycles).
Rinse aid Rinse aid dispenser is empty. (After refill the rinse
indicator is lit aid indicator may remain lit for several wash cycles).
The appliance has not been plugged in properly. Insert the plug into the socket.
Power outage.
The dishwasher
won't start or The dishwasher door is not closed.
does not respond
Cycle is interupted by door opening for more
to commands.
than 4 seconds.
It does not respond to commands.
The wash cycle has not finished yet.
The drain hose is bent.
The dishwasher
won't drain.
The sink drain pipe is blocked.
The filter is clogged up with food residues.
The dishes are rattling against each
The dishwasher
makes exces-
An excessive amount of foam has been produced.
sive noise.
The crockery has not been arranged properly.
The spray arms cannot rotate freely, being
hindered by the dishes.
The wash cycle is too gentle.
The dishes are An excessive amount of foam has been pro-
not clean. duced.
The cap on the rinse aid compartment has not
been shut correctly.
The filter is soiled or clogged.
There is no salt.
No water in the water supply or the tap is closed. Make sure there is water in the water supply or the tap running.
The dishwash-
er does not fill
The inlet hose is bent.
the water.
All LEDs are
The sieve in the water inlet hose is clogged; it
blinking rapidly
is necessary to clean it
Drain hose positioned too low or siphoning
Dishwasher
into home sewage system.
finishes the cy-
cle prematurely.
Air in water supply.
SOLUTIONS
Refill reservoir with salt (for more information - see page 5).
Adjust water hardness - see table, page 5.
Refill dispenser with rinse aid (for more information - see page 5).
For safety reasons, dishwasher will not re-start automatically when power
returns. Open dishwasher door, press START/Pause button and close the
door within 4 seconds.
Vigorously push the door until you hear the "click".
Press START/Pause and close the door within 4 seconds.
Switch off the appliance by pressing the ON/OFF button, switch it back on
after approximately one minute and restart the program. If problem per-
sists, unplug the appliance for 1 minute, then plug it back in.
Wait until the wash cycle finishes.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The detergent has not been measured out correctly or it is not suitable for
use in dishwashers (see FILLING THE DETERGENT DISPENSER). Restart the
current cycle by switching OFF the dishwasher, then switch it on again,
select a new program, press START/Pause and close the door within 4
seconds. Please do not add any detergent.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
The detergent has not been measured out correctly or it is not suitable for
use in dishwashers (see FILLING THE DETERGENT DISPENSER).
Make sure the cap of the rinse aid dispenser is closed.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the
dishwasher and reboot.
After having carried out the verification and cleaning, turn off and turn on
the dishwasher and restart a new program.
Check if end of drain hose is placed at correct height (see INSTALLATION).
Check for siphoning into home sewage system, install air admittance
valve if necessary.
Check water supply for leaks or other issues letting air inside.
EN
13