Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
4. MACHINE CHARACTERISTICS
4.1 TECHNICAL SPECIFICATIONS
BLADE DIAMETER
ARBOR SHAFT DIAMETER
CUTTING CAPACITY (TILE SIZE)
DIAGONAL CUTTING CAPACITY
(TILE SIZE)
MAXIMUM CUTTING HEIGHT
VOLTAGE
SPEED
4.2. MACHINE COMPONENTS
Know your saw and read the user manual for safe work. Before
using this product, familiarize yourself with all its characteristics,
components and safety rules.
• 7 INCH DIAMOND BLADE: Included with the machine.
• WARNING: Do not use blades with a classification lower than
the speed of this tool. Ignoring this warning could result in
personal injury.
• FOLDING STAND To hold the saw at a proper working position.
• ON / OFF SWITCH, with easy access and safety lock.
• CUTTING HEAD with adjustable angles for making miter cuts of
22.5° and 45°, and adjustable cutting depth with plunge function.
• SLIDING TABLE with bearings for smooth and accurate travel.
• ANGLE GUIDE for making repetitive cuts and angle cuts.
• REAR WATER TRAY to collect the water and keeping the work
area clean and splash-free.
4.3 PACKAGE CONTENTS
Package contents (Page 3) (Picture 2)
1. Stand components (disassembled).
2. Water tank
3. Frame
4. Sliding table
5. Cutting head and support arm assembly.
6. Splash guard.
7. Water pump.
8. Angle guide.
9. Rear water tray.
10. 7-inch cutting blade.
11. Set of tools.
12. Operating manual.
5. ASSEMBLY INSTRUCTIONS
After unpacking the machine, carefully check for damaged or
broken parts. If you find a damaged or broken part, contact
RUBI's after-sales service and replace it with an original
RUBI spare part.
Do not throw away the packaging material until you have
carefully inspected and satisfactorily used the tool. Make sure to
remove all components and accessories prior to discarding the
packaging material.
WARNING:
If a part is damaged or missing, do not use the tool until the parts
are replaced.
WARNING:
Do not connect the machine to the power source until it is
fully assembled.
- 6 -
5.1 STAND ASSEMBLY
7 IN (180 MM).
5/8 IN (16 MM)
24 IN (60 CM)
18 IN (45,5 CM)
2-1/4 IN (57 MM)
120 V/60 HZ, 10 A
6000 R/MIN. (RPM)
5.2 INSTALLATION OF THE WATER TANK
5.3 ASSEMBLY OF THE CUTTING HEAD AND SUPPORT ARM
5.4 INSTALLATION OF THE FRAME ON THE WATER TANK
5.5 INSTALLATION OF THE SPLASH GUARD
5.6 INSTALLATION OF THE CUTTING BLADE
(Picture 3 and 4)
ATTENTION! Some parts of the stand are moving parts. When
fastening the various parts of the stand, ensure that you do not
obstruct the folding parts. Fasten the stand joints so that they can
rotate, but without having any side play.
ATTENTION! To facilitate the assembly, parts that must go together
have been marked with letters. Match the letters for correct assembly.
1. Insert the lower leg section into the upper leg housing. Match the
numbers for correct assembly.
2. Assembly the front and rear legs inserting the M8 bolts through the
mounting holes.
ATTENTION! Place the spacers between front and rear legs.
3. Secure the joint with the nut in such a way that the front legs
can rotate with respect to the rear legs, but without there being
any side play.
ATTENTION! Once the stand is assembled, check that the stand
remains stable in the work position and there is no play between the
various parts.
ATTENTION! Do not attempt to mount the water tank on the stand
without having satisfactorily completed the assembly of the stand.
1. Place the folding stand in the work position on a flat surface. Ensure
that the stand remains stable.
2. Place the water tank on the stand by aligning u-shaped mounting
feature under tub on top of the stand cross-rails.
1. Place the frame on a table or working bench.
2. Align the support arm with mounting holes located on the left rear
side of the frame.
3. Fasten the support arm to the frame. First, slide metal sleeve
into larger diameter opening in each hole. Using the five M10 bolts,
washers, and nuts while you hold the support arm on place, firmly
tighten the nuts.
1. Place the frame and cutting head on the water tank, so that the
connection screws between the frame and the support arm are
located on the rear left side.
NOTE: The draining hole in on the front side of the water tank.
2. Pass the water tube through the opening provided between the
frame and water tank at the rear left side of the water tank.
NOTE: The splash guard is in two parts.
1. Tighten the rear part of the splash guard to the rear side of the
blade guard using the provided M5 screw and washer.
2. Attach the side flaps of the splash guard, wrapping them around the
rear splash guard already assembled, and secure it with the screws on
both sides of the blade guard.
ATTENTION! This saw only uses 7-inch blades. Do not attempt to use
blades of a different size, or blades with a maximum rotation speed
that is less than the speed of the saw.
ATTENTION! Unplug the saw before installing or changing the
cutting blade.
1. Open the blade cover by rotating knob COUNTER-CLOCKWISE.
2. With the provided blade wrench, engage arbor nut, depress arbor
lock located under operating handle and rotate blade until arbor lock
engages. Remove arbor nut by rotating COUNTER-CLOCKWISE with
blade wrench and remove outer arbor washer from the motor shaft.
3. With the blade directional arrow pointing COUNTER-CLOCKWISE,
fit the cutting blade on the shaft so that it rests flat against the inner
arbor washer.
4. Fit the outer arbor washer on the shaft so that it fully rests against
the blade and tighten the arbor nut by hand.
(Picture 5)
(Picture 6)
(Picture 7)
(Picture 8)
(Picture 9)
Publicidad
