Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISh
3. Depress and hold the variable speed trigger
feed the wheel into the workpiece with firm even pressure,
allowing the tool to do the work. Do not force the cut off
tool through the workpiece. Forcing a cut off tool can cause
kickback. For maximum efficiency and wheel life, keep the
wheel speed high.
4. While cutting, if using the shoe, keep the shoe against the
workpiece and maintain a firm grip.
NOTE: If making a partial cut, restarting a cut, or correcting
cut direction, allow the wheels to come to a complete
stop. To resume cutting, pull the variable speed trigger and
re-enter the cut slowly.
5. To stop tool, release the variable speed trigger.
General Tips for Cutting Materials
For best control, user cutting direction should be
-
opposite wheel rotation. Example: When making a cut
away from user by pushing the tool forward, set wheel
rotation to reverse/clockwise direction.
Be sure that the wheel is at full speed before continuing
-
a cut.
-
Allow the wheel to come to a complete stop before
raising the wheel out of the material.
Cutting Tile
-
To reduce overheating of cutting wheel or workpiece,
user may lightly wet surface.
If excessive chipping of the tile is observed, user may
-
operate tool at slower speed using variable speed
trigger to achieve a cleaner cut.
-
Cutting tile will generate debris. Guard position may be
adjusted to deflect debris away from user.
Cutting Plastic
-
Take frequent breaks to allow wheel to cool down.
If melted material or debris becomes adhered to blade,
-
shoe or guard: Release trigger. Allow unit to rest and
material to cool. Remove battery. Remove debris. Ensure
all areas around wheel including inside of guard is clear
of debris. Resume cutting operation.
Cutting Metals
Observe the following to avoid potential hazards when
cutting metals.
-
During and shortly after cutting operation the material,
wheel and metal components on the tool such as
gearcase, guard and shoe may get hot.
-
Allow these areas to cool before touching to
avoid injury.
-
Cutting metal will generate sparks. Guard position may
be adjusted to deflect sparks and debris away from user.
Cutting material and cutting wheel may have sharp or
-
jagged edges after cutting operation. Wear gloves and
use caution when touching these areas.
44
44
Transportation and Storage
4
. Slowly
During transportation and storage lock the variable speed
trigger with the lock-off button. Refer to the Forward/Reverse/
Lock Off Button section.
Remove the battery pack during the tool storage.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
Ventilation slots can be cleaned using a dry, soft non-metallic
brush and/or a suitable vacuum cleaner. Do not use water or
any cleaning solutions. Wear approved eye protection and an
approved dust mask.
Optional Accessories
Consult your dealer for further information on the
appropriate accessories.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: Electrical shock and mechanical hazard.
Disconnect the electrical appliance from the power source
before cleaning.
WARNING: To ensure safe and efficient operation,
always keep the electrical appliance and the ventilation
slots clean.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
WARNING: Since accessories, other than those offered
by STANLEY FATMAX, have not been tested with this
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only STANLEY
FATMAX-recommended accessories should be used with
this product.
WARNING: Handle and store all abrasive wheels
carefully to prevent damage from thermal shock, heat,
mechanical damage, etc. Store in a dry protected area
free from high humidity, freezing temperatures or extreme
temperature changes.
Publicidad
