KRESS KUE26 Serie Manual De Instrucciones página 11

The tool being in good condition and well
maintained.
The use of the correct accessory for the tool and
ensuring it is sharp and in good condition.
The tightness of the grip on the handles and if any
anti vibration and noise accessories are used.
And the tool is being used as intended by its design
and these instructions.
This tool may cause hand-arm vibration
syndrome if its use is not adequately
managed.
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the operating
cycle such as the times when the tool is switched off
and when it is running idle but not actually doing the
job. This may significantly reduce the exposure level
over the total working period.
Helping to minimise your vibration and noise
exposure risk.
Always use sharp chisels, drills and blades.
Maintain this tool in accordance with these
instructions and keep well lubricated (where
appropriate).
If the tool is to be used regularly then invest in anti
vibration and noise accessories.
Plan your work schedule to spread any high
vibration tool use across a number of days.
OPERATING
INSTRUCTIONS
NOTE: Before using the tool, read the instruction
book carefully.
INTENDED USE
The machine is intended for sawing wood, plastic,
metal and building materials while resting firmly on the
workpiece. It is suitable for straight and curved cuts.
The saw blade recommendations are to be observed.
Installation
Remove the battery pack (see Fig. A1)
To remove the battery pack, pull it out by pressing the
lock button on the front of the battery pack.
Install the battery pack (see Fig. A2)
Push the battery pack gently into the machine when
inserting it. Do not force it too hard.
Install the saw blade (see Fig. B1)
Caution:
• Remove all debris and foreign objects attached to the
saw blade and/or blade holder. Otherwise, the saw blade
may not be fastened enough, which may cause serious
personal injury.
• Do not touch the saw blade or workpiece immediately
after operation, because they may be very hot and cause
skin burns.
• Be sure to tighten the saw blade when cleaning. Other-
wise, it may cause serious personal injury.
• Be careful not to touch the blade edge or the sharp end
of the workpiece with your fingers when taking out the
saw blade, in order to avoid injury.
Make sure that the saw blade holder is in the released
position before installing the saw blade.
When installing the saw blade, insert the saw blade into
the saw blade holder (with the blade facing forward) until
it is locked. The saw blade can be directly moved to a
fixed position by itself, thus locking the saw blade. Pull
the saw blade gently to ensure that it does not fall during
operation.
Note: Make sure that the saw blade is installed in place.
The indicator line on the saw blade needs to be com-
pletely inserted into the quick chuck of saw blade.
Remove the saw blade (see Fig. B2)
Note: Hold the saw blade with one hand when
removing the saw blade.
Install the dust suction adapter (see Fig. B3)
Note: Insert the hook of dust suction adapter into the
hole on the base.
Fasten the dust suction adapter by tightening
the clamping screw at the front of the dust
suction adapter. The dust suction adapter can
be installed on either side (the left or right) of
the base.
Remove the dust suction adapter (see Fig. B4)
Note: Pull out the dust suction adapter by holding on
the raised point at its bottom.
Operation
Tool lift function (for switching the cutting
operation) (see Fig. C)
This tool can be used for the cutting operations that are
performed along track or in straight line (up and down).
The saw blade pierces into the workpiece forward in the
cutting stroke when the cutting operation is performed
along the track, which greatly increases the cutting
speed.
Only turn the tool lift control knob to the position of the
desired cutting operation in order to change the cutting
operation.
Refer to the following table to select the
correct cutting operation.
Position Cutting
operation
0
Cutting in
straight line
Ⅰ
Cutting along
small track
Ⅱ
Cutting along
medium track
Cutting along
Ⅲ
large track
Application
For cutting the mild
steel, stainless steel
and plastic.
For cutting the mild
steel, aluminum and
hardwood.
For cutting the wood
and plywood. For
cutting the aluminum
and mild steel quickly.
For cutting the wood
and plywood quickly.
11
EN