Gardena AquaBrush Compact 02/18V P4A Manual De Usuario página 11

2.2 Fitting the extension handle [Fig. A1]
DANGER!
v Do not use more than 1 extension handle.
1. Push the extension handle
<
. As you do so, the tab
ß
2. Tighten the union nut
3a
between the union nut and the connecting element is normal.
This makes the connection tight.
2.3 Fitting/replacing the brush unit [Fig. A1]
Only the following GARDENA brush units
• GARDENA Roller Brush Unit
• GARDENA Disc Brush Unit
Both brush units can be fitted on the extension handle or handle unit.
2.3.1 Fitting the brush unit
1. Push the required brush unit
2
handle as far as it will go. As you do so, the tab
ß
into the opening .
o
ß
2. Tighten the union nut
3b
between the union nut and the connecting element is normal.
This makes the connection tight.
2.3.2 Replacing the brush unit
ß
1. Unscrew the union nut
2. Pull the brush out of the handle unit
3. Fit the required brush as described in 2.3.1 Fitting the brush unit.
2.4 Connecting the multi-cleaner to the water supply
[Fig. A2]
The multi-cleaner is leak-proof up to a water inlet pressure of 1.2 MPa
(12.0 bar). However, for optimum cleaning results do not exceed 0.6 MPa
(6.0 bar) water inlet pressure.
The multi-cleaner can be used with or without a water supply.
1. Connect the supplied water stop hose connector
w
2. Turn the flow regulator
5
3. Connect a water hose
4. Connect the water stop hose connector
multi-cleaner.
3. OPERATION
CAUTION!
Water damage due to unintentional starting.
v Disconnect the water supply.
v
3.1 Charging the battery [Fig. O1 / O2 / O3]
CAUTION!
The voltage of the power source must match the specifications on the
type plate of the battery charger.
v Note the mains voltage.
The intelligent charging procedure automatically detects the battery's state
of charge and charges it with the optimum charging current depending on
the battery temperature and voltage.
This protects the battery and keeps it fully charged when stored in the bat-
tery charger.
1. Press the release button
C
holder .
Y
2. Remove the battery from the protective cover
3. Connect the battery charger
4. Slide the battery charger
GAR_14840-20.960.03.indd 11 GAR_14840-20.960.03.indd 11
Personal injury!
2 1
into the handle unit as far as it will go
m
must be pushed into the opening
by hand (do not use any tools). A small gap
may be used.
4
4 1
into the handle unit or the extension
m
must be pushed
by hand (do not use any tools). A small gap
by hand (do not use any tools).
3b
1
or the extension handle
x
to the water hose
to position 0.
6
to the water supply .
x
to the water inlet
Water damage!
> Y
and remove the battery from the battery
M
.
X
to a mains socket.
X Y
onto the battery .
When the battery charge indicator
the battery is charging.
When the battery charge indicator
ly green, the battery is fully charged (charging time, see 7. SPECIFICATION).
5. Check the state of charge at regular intervals while charging.
6. When the battery
ed from the battery charger
ß
.
o
3.2 Meaning of the display elements
3.2.1 Display on the battery charger [Fig. O3]
Flashing battery char-
å
ge indicator
Continuous illuminati-
on of battery charge
å
indicator
3.2.2 Battery state of charge indicator
[Fig. O4/O7]
After starting the product, the battery state of charge indicator
is displayed for 5 seconds.
Battery state of charge indicator
2
.
« ∑ €
, and light up green
« ∑
and light up green
«
lights up green
«
«
If the LED flashes green, the battery must be charged.
ç
If the error LED
5
3.3 Working position with extension handle [Fig. O5]
.
v Hold the multi-cleaner in an upright position with one hand on the han-
8
dle and the other hand on the additional handle
7
on the
3.4 Adjusting the position of the additional handle [Fig. O6]
ture will be upright with the brush touching the surface to be cleaned in the
working position.
0
1. Pull the lever
2. Tilt the additional handle
3. Release the lever
3.5 Starting/stopping the multi-cleaner [Fig. O1/O5/O7]
DANGER!
released.
v Do not bypass the safety devices or switches.
v For example, do not attach the start lever to the handle.
3.5.1 Starting the multi-cleaner
The multi-cleaner may only be used with a suitable GARDENA battery pro-
M
tective cover over the battery.
For Power+ batteries and 4.0 Ah batteries, a suitable battery protective
cover can be obtained from the GARDENA Service:
• Battery protective cover for Power+ battery
• Battery protective cover for 4.0 Ah battery
1. Before starting, check whether there are small stones in the brushes
and remove them if necessary.
Small stones could scratch the surface.
å
on the battery charger flashes green,
å
on the battery charger is permanent-
Y Y
is fully charged, the battery
X
.
The charge cycle is indicated by the flashing of the battery charge
å
indicator .
Note: The charge cycle is only possible if the temperature of the
battery is within the permissible charging temperature range, see
7. SPECIFICATION.
Continuous illumination of the battery charge indicator
that the battery is fully charged or that the temperature of the battery is
outside the permissible charging temperature range and therefore can-
not be charged. As soon as the permissible temperature range is
reached, the battery is charged.
If the battery is not plugged in, continuous illumination of the battery
å
charge indicator indicates that the mains plug is inserted in the
power outlet and the battery charger is ready for operation.
N
on the product
Battery state of charge
67–100% charged
34–66% charged
11–33% charged
0–10% charged
is lit or flashing, see 6. TROUBLESHOOTING.
.
9
to the desired position.
0
again until it engages.
Personal injury!
can be disconnect-
å
indicates
N
9
.
-
Art. 14800-00.600.36
Art.14800-00.600.32
11
07.02.2024 09:13:45 07.02.2024 09:13:45