Publicidad
Idiomas disponibles
Idiomas disponibles
EN
INSTRUCTION MANUAL
Ref. DM TEC B1B, DM TEC B1N and DM TEC B1P
BLUETOOTH MOTION SURFACE CEILING
DETECTOR
TECHNICAL SPECIFICATIONS
Power supply
Own Consumption
Charge
LED
Incandescent lamps
Halogen lamps 230V
Halogen + electronic
transformer
Halogen +
ferromagnetic
transformer
Fluorescent
Relay status NO or NC
Detection angle
Detection field
Adjustments
Brightness Level
Timing
Sensitivity
Protection
Working
temperature
CHARACTERISTICS
● "3 in 1" indoor detector, for flush ceiling mounted with the following
operating modes:
● It has a switching channel with a 16A relay.
● ZCT (Zero Crossing Technology), which allows to protect the
contactors of the relay and manage high loads.
● Highly sensitive PIR sensor, which detects the slightest movement
within its coverage area.
● It incorporates a red LED indicator that helps test the correct motion
detection of the device.
● It incorporates a blue LED indicator to identify that the detector is
Bluetooth enabled.
● Configuration and adjustment through the DINUY CONFIGURE App.
FUNCTIONING
● This multifunction detector can be configured in any of the
following operating modes
- Motion Detector: Detects small movements based on the
temperature difference and measures the brightness only when
the luminaire is off. Once the luminaire is switched on, it will not
be switched off until there are no people present.
Typical application example: Transit areas, corridors.
- Presence Detector: Detects small movements based on the
temperature difference and measures luminosity constantly.
Typical application example: Work areas and constant
presence. Offices.
- Twilight Switch: Lighting control based on the amount of
exterior lighting.
Typical application example: Areas affected by exterior lighting.
● This detector automatically switches the lighting based on the
detection of the slightest movement of people and the level of
natural light.
● Possibility of connecting several detectors in parallel, which makes it
possible to expand the area to be covered in a single lighting line.
● In Presence Detector mode, while the lighting is on due to the
presence of a person within its coverage area, the sensor will
compare the measured natural light with the setpoint set in the
configuration (Brightness Parameter):
- If the natural light is below the set Brightness setting, the timing
will reset when new movement is detected and the lighting will
continue on.
- If the natural light is above the Brightness setting, the timer will not
reset when new movement is detected and the lighting will turn off
when the time set in the Timer expires.
DIMENSIONS
MOUNTING
● A. Choice of location:
Since the detector responds to temperature changes, please
avoid the following conditions:
- Avoid pointing the detector towards areas or objects whose
surfaces are highly reflective or subject to rapid changes in
temperature.
- Avoid mounting the detector near heat sources, such as
convectors, air conditioners, dryers...
- Do not direct the detector towards light sources.
- Avoid directing the detector towards objects that move with the
wind, such as curtains or small trees or bushes. Consider the
direction of movement when installing the detector.
Lateral movement:
Greater sensitivity
● B. Access terminals, anchors and potentiometers:
To access only to separate the cover.
● C. Mounting:
COVERAGE
It is recommended to mount the detector at a height of 2.5m, thus
achieving a detection area of 7m in diameter.
Area of max. sensitivity
- Motion Detector;
- Presence Detector;
- Twilight Switch.
45mm
35mm
230V~ ±10% ~50/60Hz
16A cos φ = 1
400W
3.000W
3.000W
3.000W
2.400W
1.300W (130µF)
Select from DINUY Configure APP
Circular, 360º
360º in a maximum of Ø7m
with 2,5m height and 18ºC
DINUY Configure App
5 to 2000Lux, or Disabled
1 seg. till 60 minutes
5 values adjustable through
DINUY Configure App
IP40, Class II
–10ºC .. +45ºC
Movement towards the center:
Lower sensitivity
Ø
3m
Ø
7m
<1W
118,5mm
2,5m
Publicidad
