Declaration Of Conformity; Technical Specifications; Installation Instructions - Genius SHUTTER Serie Manual De Instrucciones

The central gearmotor for shutters conforms to the following technical regulations:
UNI EN 292 part I / UNI EN 292 part 2 / UNI EN 294 -UNI EN 418 / CEI En 60335-1 / D.L.vo.277 dated 18/08/91/ EN 55014-
and to the following European directives:
Shutter Model
Power supply voltage (V)
Power frequency (Hz)
Torque (Nm)
Max. weight of the locking (Kg)
Power (W)
Absorption (A)
Thrust capacitor (µF)
Heat protection (°C)
Motor insulation class
Maximum operating time (Min.)
Maximum travel (m)
Crown wheel diameter (mm)
Tube diameter (mm)
Operating ambient temperature (°C)
Overall dimensions (mm)
The diameter of the crown wheel can be modified to Ø220 mm using the plastic strip – see figure 1.

2. INSTALLATION INSTRUCTIONS

1. Drill a Ø10 mm hole at 5 cm from the centre of the
shutter shaft (see Fig. 2);
2. Remove the HH M10 screw from the gearmotor's
crown wheel;
3. Remove the two half-crowns, unscrewing screws M8
(with a 6 mm hexagonal wrench;
4. Remove delicately, without bending, the roller carrying
strip in black plastic;
5. Separate the two gearmotor elements (top and
bottom body), using the four M8 screws (with a 6mm
hexagonal wrench);
For models 15 / 15R, if the shaft of the rolling shutter
6.
is below 60 mm, use the relevant reduction sleeves
positioning them with reference to the hole Ø10 mm
previously drilled (point 1);
7. Couple the bottom body to the top body with the four
M8 screws you had removed;
8. Fasten (with 17 mm wrench) the M10 HH screw, without
hexagon nut and make it penetrate inside the shutter
shaft into the 10 diam hole (previously drilled);
9. Fit the roller strip in its seat;
Fit the half-crowns, tightening them with the two M8
10.
screws;
11. Fit the M10 HH screws with nut to fasten the gearmotor
on the shaft, and tighten the nut;
12. Place the last sheet of the shutter on the crown and
drill a 12 diam. hole in the position of the M10 threaded
hole on the crown;
13. Turn the crown wheel with your hands by 1 to 1.5 turns,
in this way bringing the knob toward the microswitch I
(descent), fig.2 (must rotate freely);
14. Tighten the shutter to the gearmotor with the M10 HH
screw, with washer (using the 17 mm wrench);
15. Make the electrical connections described in fig. 2
SHUTTER

1. DECLARATION OF CONFORMITY

1 / En 55014-2
98/37/EEC / 73/23/EEC / 89/336/EEC

1. TECHNICAL SPECIFICATIONS

15
200 / 60
230 115
50 60
145
250
630 610
2.7 5.2
20 70
200
60
200 x 380
16.
17.
18.
19.
1.
2.
3.
6
15 R 20
200 / 60 240 / 76
230 115 230
50 60 50
155 210
270
630 610 630
2.7 5.2 2.7
20 70 20
160
B
4
6
-20 - +55
240 x
200 x 330
380
routing the 4x1 mm supplied cable inside the shutter
2
shaft, thus avoiding contact with the rotating parts;
After you have completed the mechanical installation
and the electrical contacts, adjust the travel limit
devices;
Manually rotate the travel limit knob until you can
hear the click of the microswitch snap (descent
adjustment done);
Turn the other knob, taking it near to microswitch II
(rise). Power up the gearmotor with the selector switch
or push button to verify if, when the shutter rises, stops
in the required point. To adjust the position, use the
same knob, always working strictly with the electrical
commands, absolutely avoiding any manual lifting
operations;
If the installation is contrary with respect to figure 1,
work differently to what we have described, because
microswitch II will stop descent, whereas microswitch
I will stop the rise.
2. WARNINGS
This handbook is an integrated and essential part of the
product and must be delivered to the user. Carefully
read the warnings in this handbook, because they
provide important indications concerning the safety
of installation, use and maintenance. Carefully store
this handbook for all further consultation.
When you have removed the packing, make sure that
the equipment is in good condition. In case of doubt,
do not use the equipment and contact professionally
qualified personnel. Packing materials (plastic bags,
polystyrene foam, nails, etc.) must not be left within
the reach of children, because these materials are
potential danger sources.
Before connecting the equipment, make sure that
20 R B 40 B 42 R
240/76 240 / 76 240 / 76
230
50
200 400 420
430
1260
5.4
2 x 20
240
76
240 x 240 x 240 x
330 380 330