EINHELL TC-SS 406 E Manual De Instrucciones Original página 20

•
Extractor adapter
•
2.5 mm hex key
•
4 mm hex key
•
Spare pinned fretsaw blade
•
Original Operating Instructions
•
Safety Information
3. Proper use
The fretsaw is intended for cutting square-edged
timber or wood-like workpieces. Round materials
may only be cut with suitable holding devices.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case
of misuse. The user / operator and not the manu-
facturer will be liable for any damage or injuries of
any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The equipment is to be operated only with suita-
ble saw blades. It is prohibited to use any type of
cutting-off wheel. To use the equipment properly
you must also observe the safety regulations, the
assembly instructions and the operating instruc-
tions to be found in this manual.
All persons who use and service the equipment
have to be acquainted with this manual and must
be informed about the machine's potential ha-
zards.
It is also imperative to observe the accident pre-
vention regulations in force in your area.
The same applies for the general rules of health
and safety at work.
The manufacturer will not be liable for any chan-
ges made to the machine nor for any damage
resulting from such changes.
Even when the equipment is used as prescribed
it is still impossible to eliminate certain residual
risk factors. The following hazards may arise in
connection with the machine's construction and
design:
•
Harmful emissions of wood dust when used
in closed rooms.
•
Contact with the blade in the uncovered cut-
ting zone.
•
Injuries (cuts) when changing the blade.
Anl_TC_SS_406_E_SPK13.indb 20 Anl_TC_SS_406_E_SPK13.indb 20
GB
•
Crushed fingers.
•
Kickback.
•
Tilting of the workpiece due to inadequate
support.
•
Touching the blade.
This appliance is not intended for use by persons
(including children) with reduced physical, sen-
sory or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
4. Technical data
AC motor: ....................................... 230 V~ 50 Hz
Power consumption: .....S1 70 W · S6 30% 120 W
Idle speed n : ...............................400-1600 min
0
Stroke: ...................................................... 14 mm
Tilting range of table: ............................ -2° to 47°
Table size: ..................................... 415 x 250 mm
Blade distance from the lateral pins: ...... 127 mm
Tooth pitch in teeth per 25.4mm:
............................................15 tpi (teeth per inch)
Throat: .................................................... 406 mm
Max. cutting height at 90°: ........................ 50 mm
Max. cutting height at 45°: ........................ 23 mm
Dust extraction connector: ....................... 36 mm
Weight: ............................................ approx. 9 kg
Permitted length of a coping blade: 128-134 mm
Operating mode S6 30%: Continuous operation
with idling (cycle time 10 minutes). To ensure that
the motor does not become excessively hot, it
may only be operated for 30% of the cycle at the
specifi ed rating and must then be allowed to idle
for 70% of the cycle.
Danger!
Noise
The noise emission values were measured in ac-
cordance with EN 62841.
Operation
L sound pressure level ........................ 71 dB(A)
pA
K uncertainty ........................................ 3 dB(A)
pA
L sound power level .......................... 84 dB(A)
WA
K uncertainty ........................................ 3 dB(A)
WA
- 20 -
-1
05.06.2023 13:37:29 05.06.2023 13:37:29