osann Juntos Manual Del Usuario página 18

EN
1) Unfold the frame
Unfold the frame by fi rst releasing the transport
lock (A), then pressing the button on the height ad-
justment slider (B) and pulling it upwards until the
frame is unfolded. Without sports buggy attach-
ment Press the adapter unit on its crossbars from
bottom to top until you hear a click. Check that the
frame is fully engaged.
With sports buggy attachment Pull the backrest
upwards from below until you hear a click and the
adapter unit is automatically locked into position.
Check that the frame and sports buggy attachment
are fully engaged.
2) Mount the front wheels
Insert the front wheels into the front axle until you
hear a click. Check that the front wheels are fully
engaged. To remove the front wheels again, press
the button on the inside of the front axle (A) and pull
the wheels out of the axle.
3) Mount the rear wheels
Insert the rear wheels into the rear axle until you
hear a click. Check that the rear wheels are fully en-
gaged. To remove the rear wheels again, press the
button on the underside of the respective rear axle
(A) and pull the wheels out of the axle.
4) Guard bar for sports buggy attach-
ment
Insert the guard bar into the openings provided on
the sports buggy attachment until you hear a click.
Check that the guard bar is fully engaged. To re-
move the guard bar again, press the button (A) on
both sides of the guard bar and pull it away from
the sports buggy attachment. The guard bar can be
opened and unfolded on one side to make it easy to
put your child in.
5) Sports buggy attachment
Insert the sports buggy attachment into the des-
ignated sockets on the frame until you hear a click.
Check that the sports buggy attachment is ful-
ly engaged. The sports buggy attachment can be
mounted on the frame either in the direction of
travel or facing the pushchair. To dismantle the at-
tachment again, press the buttons (A) on both sides
of the attachment and pull it off the frame.
- 18 -
6) Assemble the carrycot
First remove the mattress. Open the inner zip of the
carrycot so that you can remove the inner cover.
Push the metal brackets from the inside to the out-
side into the fi xings so that the carrycot opens up.
Check that the metal brackets are fully engaged in
the fi xing points. Reinsert the cover and close the
zip. Put the mattress back in. Model-dependent:
The front sun visor on the cover of the carrycot can
be removed for transport reasons. Reattach it to the
cover using the zip fastener.
7) Sports buggy attachment belt sys-
tem
The belt system is individually adjustable in both
the shoulder and pelvic areas. The shoulder straps
can be infi nitely adjusted in height. Babies and tod-
dlers under 6 months: Please use the lowest height
setting for the shoulder belts.
8) Front wheel swivel function
You can lock or swivel the front wheels using the le-
ver on the front wheel.
9) Brake
Press the brake down to lock it. To release it, press
it upwards again.
10) Adjusting the push handle height
Press the button (A) on the push handle, pull or
push the push handle to the desired height and re-
lease the button. Check that the push handle is fully
engaged in the desired position.
11) Adjust the backrest
Pull the lever at the top of the backrest and adjust
to the desired position. Check that the backrest is
fully engaged in the desired position. Babies and
toddlers under 6 months: Please use the lowest
backrest setting and adjust the leg support to the
horizontal position.
12) Adjusting the canopy height
The height of the pushchair canopy can be adjusted
in 3 positions. To do this, press the button (A) on the
back of the backrest and set the desired position.
Attention: To fold the frame with the pushchair
attachment, the canopy must be set to the low-
est position.
13) Adjusting the leg support
Press the button (A) on both sides of the leg sup-
port and set the desired position. Check that the
leg support is fully engaged in the desired position.