Beurer MG 330 Instrucciones De Uso página 15

1
the neck section to engage. The neck section
fixed in place and you can remove your hands from the device.
2. Adjusting the tilt: (The corresponding drawing B is shown on
page 5.) To adjust the tilt, hold one hand on the neck section
1
and the other on the back section
cover. At the start of the adjustment, move the neck section
1
backwards until you hear it engage. The neck section
now in line with the back section
1
section forwards until it has reached the optimum position
for you. The neck section
lease it, move the neck section
position. The neck section
readjust, lift the neck section
6.3 Starting use
 CAUTION
Do not force or jam any part of your body, in particular your fin-
gers, between the rotating massage heads
in the device.
At first, just press your back carefully against the
Shiatsu seat cover. Then check carefully whether
the massage position is pleasant for you and then
shift your weight gradually towards the Shiatsu
seat cover.
The massage should feel pleasant and relaxing at
all times. If the massage is painful or uncomforta-
ble, stop the massage or change your position or
the contact pressure.
1. Selecting the seat position: Sit comfortably and upright on
the Shiatsu seat cover. Take care to ensure you are positioned
in the middle of the massager and that the massage heads
can move to the left and right of your spine.
2. Switching on the device: Switch on the Shiatsu seat cover
with the ON/OFF button
back section 5 switch on automatically.
3. Selecting the massage area for the back: Use the UPPER
BACK button (upper back)
(lower back) to select the area you want to have massaged.
13
The LED lights on the hand switch
sage area. The rotating massage heads
wards from the starting position in the lowest area of the back
and then move up and down in the set massage area (upper
or lower back).
4. "SPOT" massage: Press the SPOT button
in a specific spot in the back area. Use the arrow buttons
to freely adjust the massage area up and down.
5. "NECK" massage: Press the NECK button
massage in the neck area. Pressing the NECK button
will change the direction of rotation. Press the NECK button
again in order to switch o the massage in the neck area. The
LED light for "NECK" on the hand switch will go out.
6. Maximum application time/automatic switch-o : As soon
as the Shiatsu seat cover is switched on, the automatic switch-
o function will be activated automatically and preset to 15
minutes.
1
4
to stabilise the seat
5 . Now you can tilt the neck
1
is now fixed backwards. To re-
1
down once to a 90 degree
1
can now be moved freely. To
1
up until it engages.
2 4
, or their holders
. The massage heads
18 4
or the LOWER BACK button
12
indicate the set mas-
8
4 travel slowly up-
14 to start usage
11
to activate the
11
is now
 CAUTION
Use the massager for max. 15 minutes and then leave it to
cool down. Long massages can lead to over-stimulation
of the muscles, creating tension instead of aiding relax-
ation. You can end the massage at any time by pressing
the ON/OFF button
1 will return to their start position in the lumbar area when
is
the device is switched o . This is indicated by a flashing
LED light. Once this position is reached, the Shiatsu seat
cover switches o .
7. At the end of use: Do not disconnect the Shiatsu seat cover
from the power supply while it is in operation. Always switch
it o first and then wait until it has reached its start position.
6.4 Other applications
Seat cover
The seating surface of the massage seat cover is attached to the
back area via a zip fastening. You can open this to use the seat
cover separately. You can also use it as a back rest.
Combination with heat pad
The massage seat cover can also be used with all beurer heat
pads measuring 40 x 30 cm / 44 x 33 cm. To do this, place the
heat pad in the cover via the zip fastening on the underside of the
seat cover. The heat pad should lie on the inner padding in the
direction of the seating surface. The cable for the heat pad can be
guided out through the buttonhole on the side of the seat cover.
It can be used during the massage as well as also separately for
the back or the feet.
To purchase beurer heat pads, visit the webshop www.beur-
er-shop.de
7. CLEANING AND MAINTENANCE
4
Cleaning
 CAUTION
in the
• Unplug the device each time before cleaning.
• Clean the device using only the methods specified. Liquid
must not penetrate the device or the accessories under any
circumstances.
• Small marks can be removed using a cloth or damp sponge,
and some liquid delicate laundry detergent where necessary.
Do not use any solvent-based cleaning products.
• The removable covers of the seat and neck area are washable
at 30°C. Please note the symbols for care and cleaning on the
label sewn into the cover.
• Do not use the device again until it is completely dry.
15
• You can remove the neck cover by releasing the hook-and-
loop fastener. The seat section can be removed from the back
section using the zip fastening. Before washing, open the zip
fastening on the seat cover and remove the padding. Once
again
the covers have dried, you can reattach them.
11
Care
If you do not plan to use the device for a long period of time,
we recommend that you store it in the original packaging in a dry
environment, ensuring it is not weighed down by additional items.
15
. Note that the massage heads
18 4